Top End Rebuild Kit MC18, Cyl. C, Assy.
€293.88
Below is everything you need to do a top end rebuild on your MC18. Suitable for cylinder ‘C’. One kit includes all parts for one cylinder. To overhaul both cylinders please order 2 kits.
There are different kits depending on the piston supplied and the pistons are sized to match the cylinder. The cylinders have a letter stamped on them. A cylinder = B piston B cylinder = no mark piston, C cylinder = D piston. The largest cylinder bore is A and the smallest is C. However, note that this is only for when cylinders are new or in good condition, so if the cylinder is worn, the corresponding piston will be a looser so a bigger piston might be advised. If the cross hatch honing of the cylinder is very feint then we suggest using the next size up piston. The differences in sizes are tiny (11 microns between largest and smallest) and for the most part not an issue so it is not a problem if a smaller piston is used in a larger cylinder or the other way round.
Cylinder A = 54.008mm – 54.011mm use Piston B = 53.966mm – 53.969mm
Cylinder B = 54.004mm – 54.008mm use Piston # = 53.962mm – 53.965mm
Cylinder C = 54.000mm – 54.004mm use Piston D = 53.958mm – 53.961mm
Piston to bore clearance = 0.039mm – 0.045mm
TYGA no: NHPS-0002C
SKU: hon-10877 Categories: ALL products, High performance, High performance, Honda, New OEM Honda parts, NSR250, NSR250 MC18Set full race system under belly with long stainless silencer with carbon cap, Honda Monkey 125 2018-
€480.85
Set, Pipe, Full System, Underbelly, Monkey 125, Stainless Oval/Carbon End Cap, Long
This full race system has been specifically designed for the Monkey 125 to maximise power. Made in stainless steel with spring mounted carbon silencer this system increases performance, saves weight and enhances the looks of the bike. Sounds great too! (A dB killer is included).
Note that once the stock system has been removed from the Monkey, there is an empty space under the seat on the right side. We recommend installing TYGA Performance product BPCC-7142R which has been designed to mirror the left side cover. This will fill in the gap under the seat and complete the transformation. Refer to photos of the exhaust installed for more details.
See also set with the Carbon Side Cover Included : EXPS-0107
Performance and Dynograph
The blue trace shows the 100% standard Honda Monkey 125, compared to the red trace, which is after installing the TYGA Full System set (EXPS-0109) with no other changes to the stock bike.
A useful increase in peak power and further gains could probably be had with remapping etc.
Similar Products:
Please also see:
EXPS-0110 Stainless, Underbelly, with short silencer
EXPS-0107 Stainless, Underbelly with long Silencer and Carbon side Cover
EXPS-0108 Stainless, Underbelly with short Silencer and Carbon side Cover
Meter Stay Extension
€12.29
Replacement meter stay extension nylon shaft. Suitable for the following models:
BPFS-0012
BPFS-0019
BPFS-0032
BPFS-0033
See table for application of meter stay extensions with our body kits:
Front spacer wheel kit, fork conversion CBR600RR 05-06.
€36.64
Wheel, Front, Spacer Kit. ’05-’06 CBR600RR fork conversion.
These spacers are designed to allow the standard NSR250, NC30/35 front wheel to be used together with the ’05-’06 model CBR600RR forks when used with our CBR600RR triple clamp conversion.
Note that the upper/lower triple clamp bore dimensions are 48mm – 53mm.
The standard ’05-’06 axle shaft is too large a diameter to fit the NSR/NC wheel, so these spacer bushes are used to allow the use of the smaller axle shaft. The standard NSR250/NC30 shaft is a little too short, so we recommend using an RVF400 axle.
The NSR/NC disc mounting face is 100mm wide. The disc pitch, centerline to centerline of the rotors should be 138mm, and the discs 310mm in diameter.
RVF750R RC45 or NR750 discs can be used
TYGA no: TPER-0065
SKU: hon-10962 Categories: ALL products, High performance, Honda, NSR250, NSR250 MC18, NSR250 MC21, NSR250 MC28, Various parts, Various parts, Various partsSilencer GP-T, Aluminium 60mm, Two Stroke, Spring Mounted
€95.39
Silencer GP-T, Aluminium, Two Stroke, Spring Mounted, Assy
To complement our NX5 exhaust chambers, we wanted a silencer design which was both functional and classic. The result is this TYGA Performance GP-T style silencer. Available in three models, with carbon, carbon/Kevlar and aluminium outer tubes and with stainless end caps, it is mounted by two springs (included) for ease of installation and for looks. The silencer is strong and easily rebuildable, using rivets to assemble. Remember to order two silencers for every twin cylinder exhaust system! Also see EXSL-0069 and EXSL-0069.
Note, this silencer is only compatible with the NX5 RS250R exhaust system and cannot be mounted on other exhaust chambers in our product range.
TYGA no: EXSL-0070
SKU: hon-10903 Categories: ALL products, CNC parts, Exhaust, Honda, RS250R NF5 / NX5, ShopMeterstay aluminium Race , Honda VFR400 NC30
€202.46
Meter Stay, NC30, Race, Stock Type, Assy
This meter stay to be used with all stock shaped bodywork. It is the same dimensions as Honda part 64501-MR8-000 and TYGA part TYLY-0016 but is designed with track use in mind . Made from aluminium and designed without any headlight mounts, this simple and lightweight stay is suitable for race and track day applications.
Compatible with stock Honda NC30 bodywork and TYGA parts BPFU-1021 and BPFS-0139
TYGA no: TYLY-0250
SKU: hon-11215 Categories: ALL products, Honda, Shop, Various parts, VFR400RR NC30Seat cowling stock shape painted RT, Honda RVF400 NC35
€419.72
Stock shape seat cowling with or without taillight holes. Single seat, direct replacement for stock NC35 seat cowling in the same shape but with the exact top part of the RC45 single seat replacing where the passenger seat was. This seat cowling uses OEM seat pad. Please specify if you would like taillight holes and taillight mount made for no extra charge. If we receive no comment, we will send with taillight holes and mounts.
Compatible Parts:
All Tyga Performance and Honda OEM panels. Retains use of Honda OEM taillight and seat pad
Painted in classic RT scheme (1996-2000). This panel is finished to match the stock paintwork
TYGA no: BPFT-9004 (Painted RT)
SKU: hon-10520 Categories: ALL products, Bodywork, Bodywork and carbon, Bodywork and carbon, Honda, RVF400RR NC35, ShopTop Triple clamp CNC black , Suzuki RGV 250
€218.46
CNC machined TYGA top triple clamp ( without detachable key holder for race use) for your RGV250 VJ22.
Designed and machined in house by TYGA, as a direct replacement for the OEM top triple clamp. FEA tested and developed for increased strength without unnecessarily increased weight.
Crafted from aircraft spec 6061-T6 alloy, the top triple clamp is ready to fit.
The detachable ignition switch holder can be ordered separately or together with this product as set TYLY-1046.
TYGA no: TYLY-1046(p)
SKU: suz-10056 Categories: ALL products, CNC parts, CNC parts, RGV250 VJ22, Shop, Suzuki