Carbon holder brake hose "NSR500V style), NSR250 MC28 – NC30 – NC35
€45.78
Holder, Carbon, Brake Hose, NSR500V Style
This carbon brake holder is a faithful reproduction of HRC part 43150-NX6-000 used on the HRC NSR500V GP bike.
It allows for removal of the stock chain guard by providing a safe way of securing the rear brake line on any Pro Arm model such as the MC28, NC30 and NC35. To install this holder, it is necessary to drill and tap two small mounting holes in the swing arm to secure the holder using the bolts and washers provided with the holder. The holder is also supplied with cable ties and rubber hose suitable for braided brake lines in order to keep the brake line held in position while at the same time looking neat and tidy.
Important: care should be taken during installation to allow adequate clearance of the brake line with the chain and rear wheel when the bike is being ridden allowing for movement due to suspension etc.
TYGA no: BPCC-0051
SKU: hon-11203 Categories: ALL products, Bodywork and carbon, High performance, Honda, NSR250, NSR250 MC28, NSR500V NX6, RS250R NF5 / NX5, RVF400RR NC35, Various parts, Various parts, Various parts, Various parts, VFR400RR NC30Silencer, Stainless Moto Maggot, Left, KTM RC390 Serpent, No fittings
€205.51
Silencer, Stainless Moto Maggot, Left, KTM RC390 Serpent, No fittings
Maggot silencer with 35 mm. inside diameter. Does not include pipe section or springs
TYGA no: EXSL-8113L(p)
SKU: ktm-10122 Categories: ALL products, Exhausts, Exhausts, KTM, RC 390, Stock list, all modelsCarbon cover, temp Gauge 64mm, Honda
€25.10
Carbon cover, temp Gauge 64mm, Honda
This cover fits snuggly over the original plastic Honda gauge cover and adds a sporty appearance. It is also ideal for hiding any ugly scratches or dents that may have occurred over the years. Fits in second and can be held in place with a dab of glue or silicone adhesive.
This product is suitable for the following models:
MC18 NSR250
NC30 VFR400R
RC30 VFR750R
Also available as a complete set with speedo,temp gauge and rev counter, see BPCC-0027
This product might also fit other models.
TYGA no: BPCC-0024
SKU: hon-10609 Categories: ALL products, Carbon, CBR400RR NC23, Honda, NSR250 MC18, Shop, Various parts, Various parts, VFR400RR NC30carbon rear hugger STD wheel, VFR400
€308.02
Rear Hugger (Carbon), VFR400R NC30, Assy.
New stylish design prevents water and road debris from the rear wheel reaching the rear shock and other components. Please note this model is designed specifically for the NC30 VFR400R with the stock 150/18 rear tyre fitment. Note we make similar products:
BPCH-7014, NC35 150/17 tyre size
BPCH-7024 NC35 160/17 tyre size
TYGA no: BPCH-7004
SKU: hon-10564 Categories: ALL products, Bodywork and carbon, Bodywork and carbon, Carbon, Honda, Shop, VFR400RR NC30Carbon rear hugger, KTM RC125/RC200/RC390 2022-
€113.63
Set pipe Full race system WSS300 (race), KTM RC390
This full exhaust system has been conceived to meet WSS300 specifications and carefully designed to squeeze the most power out of the 390. The stainless steel headers are tapered and the sections hand- rolled and welded to give this system incredible looks as well as performance.
And with full spring mounting, fitting and removal of the exhaust is quick and simple. Ideal in a race environment.
By taking advantage of better routing under the engine, the exhaust can be made to optimize dimensions to exploit the motor’s full potential. In addition, by tucking it up through the swing arm, the exhaust does not have any clearance issues in tight bends and is kept away from side which is the most vulnerable position in the case of an accident, increasing its survivability.
The system features a primary silencer, which helps reduce the sound level without any loss of performance.
The system is also provided with a dB killer as well as a carbon heat shield and a bracket so you can mount this system on the earlier RC390 models which did not have this already on the frame, meaning this exhaust will fit all RC390 models to date.
Sound test of the full TYGA system back to back with the Akrapovic World Supersport 300 titanium pipe.
As you can see on the chart below, the sound levels (without DK) are pretty much identical between the two systems. The DK knocks about 5 decibels off everywhere.
Due to the new routing of the exhaust, it is necessary to re-route the water hoses and remove the thermostat, and we provide all the necessary hoses for this conversion. Also, due the exhaust running under the engine, the stock belly pan is not compatible and we provide some alternatives which are not included in the cost of the exhaust.
Note, this is what we describe as the ‘Street’ system. The only difference between this and the race one is the silencer is in a more out board position to clear license/Registration place when used on the street. Powerwise, it is identical to EXPS-0112
TYGA no: BPCH-7031B
SKU: ktm-10206 Categories: ALL products, Bodywork and carbon, Exhausts, KTM, RC390 2022-, Stock list, all modelsFitting kit for Belly pan, KTM RC
€30.90
Fitting kit for Belly pan
This mounting kit is for our belly pan:
BPFL-7231
BPCL-7231
BPFL-7331
BPCL-7331
TYGA no: TYBP-?
SKU: ktm-10171 Categories: ALL products, Bodykit replacement parts, Bodywork, Bodywork and carbon, KTM, RC 390Carbon shroud (pair), Honda MSX125 2021-
€451.95
Carbon front fender “sport style”, Honda MSX 125 (MK1 MK2) Monkey 125 2018-
Sports style Carbon front fender to give your Monkey 125 or MSX125 Grom* a clean and unique appearance. Easy install with mounting bolts provided.
See also BPFF-7142 for GRP version.
*Note that when this fender is installed on the MSX125 Grom, it uses using just the four bolts in front of the fender and the two mounting holes behind the fork leg for the stock fender on the Grom are not used. For the Monkey, it mounts on the fork guard mounting holes.
TYGA no: BPCX-7248
SKU: msx-10501 Categories: ALL products, Bodywork and carbon, Honda, MSX125 2021-, ShopTop Triple clamp CNC black , Suzuki RGV 250
€218.46
CNC machined TYGA top triple clamp ( without detachable key holder for race use) for your RGV250 VJ22.
Designed and machined in house by TYGA, as a direct replacement for the OEM top triple clamp. FEA tested and developed for increased strength without unnecessarily increased weight.
Crafted from aircraft spec 6061-T6 alloy, the top triple clamp is ready to fit.
The detachable ignition switch holder can be ordered separately or together with this product as set TYLY-1046.
TYGA no: TYLY-1046(p)
SKU: suz-10056 Categories: ALL products, CNC parts, CNC parts, RGV250 VJ22, Shop, Suzuki