Carbon chain guard, KTM RC125/RC200/RC390 2022-
€141.35
Set pipe Full race system WSS300 (race), KTM RC390
This full exhaust system has been conceived to meet WSS300 specifications and carefully designed to squeeze the most power out of the 390. The stainless steel headers are tapered and the sections hand- rolled and welded to give this system incredible looks as well as performance.
And with full spring mounting, fitting and removal of the exhaust is quick and simple. Ideal in a race environment.
By taking advantage of better routing under the engine, the exhaust can be made to optimize dimensions to exploit the motor’s full potential. In addition, by tucking it up through the swing arm, the exhaust does not have any clearance issues in tight bends and is kept away from side which is the most vulnerable position in the case of an accident, increasing its survivability.
The system features a primary silencer, which helps reduce the sound level without any loss of performance.
The system is also provided with a dB killer as well as a carbon heat shield and a bracket so you can mount this system on the earlier RC390 models which did not have this already on the frame, meaning this exhaust will fit all RC390 models to date.
Sound test of the full TYGA system back to back with the Akrapovic World Supersport 300 titanium pipe.
As you can see on the chart below, the sound levels (without DK) are pretty much identical between the two systems. The DK knocks about 5 decibels off everywhere.
Due to the new routing of the exhaust, it is necessary to re-route the water hoses and remove the thermostat, and we provide all the necessary hoses for this conversion. Also, due the exhaust running under the engine, the stock belly pan is not compatible and we provide some alternatives which are not included in the cost of the exhaust.
Note, this is what we describe as the ‘Street’ system. The only difference between this and the race one is the silencer is in a more out board position to clear license/Registration place when used on the street. Powerwise, it is identical to EXPS-0112
TYGA no: BPCX-7131B
SKU: ktm-10207 Categories: ALL products, Bodywork and carbon, Exhausts, KTM, RC390 2022-, Stock list, all modelsHandlebar Clamp, Left, Black, 50 mm.
€98.58
Handlebar Clamp, Left, Black, 50 mm.
Replacement handlebar clamp for handle bar set TYLY-1078
Side cover left black, Honda MSX125 GROM
€39.31
SIDE COVER LEFT BLACK, HONDA MSX125 GROM
Carb Service Kit A, 32 pieces, Honda VFR400R NC30
€61.57
Carb Service Kit A, 28 pieces, Honda VFR400R NC30
LiteTek Carburettor Seal Kit to suit
Honda VFR400R NC30
Made from long lasting, ethanol resistant elastomers and Viton®
Consist of the following items:
4x FB-003 Float Bowl Ring, Material: Flourosilicone (Part of Honda Kit 16010-MR8-505)
4x OR-005 Pilot Screw O-Ring, Material: Viton 70A (Part of Honda Kit 16010-MR8-505)
4x WS-001 Pilot Screw Washer, Material: Stainless Steel
4x OR-009 Drain Screw O-Ring, Material: Viton 70A (Part of Honda Kit 16010-MR8-505)
4x OR-011 Float Bowl Vent O-Ring, Material: Viton 70A (Part of Honda Kit 16010-MR8-505)
4x OR-012 Fuel T-Pipe O-Ring, Material Viton 70A (Part of Honda Kit 16010-MR8-505)
4x CS-004 Choke Plunger Cap, Material: HNBR (Part of Honda Assy. 16046-MG9-681 or 16047-ML7-004)
TYGA no: CK-Honda-NC30
SKU: alg-10352 Categories: ALL products, Carburettor Service Kits,, Honda, Shop, Various parts, VFR400RR NC30Silencer stainless round, 2" x 380mm
€230.91
Silencer, Stainless, Round, 2" x 380 mm., Assy
This silencer has polished stainless steel endcaps and a hairline finish stainless tube for a lightweight and attractive finish. Free flowing, this silencer not only allows for more power but gives a much more rewarding audible experience over stock. This system may not comply to specific country noise emission regulations and is not homologated for street use.
The ‘slip-on’ mount is designed to fit any system with a 2" external diameter tail pipe. It is secured in place with two springs, which align with the spring hooks already fitted to the TYGA pipe. A silencer mounting clamp is also provided to secure the silencer to the bike.
Two extra (stainless) spring hooks are included and can then be welded to any other system that may need modification to fit the silencer.
Compatible with TYGA and other systems which use a 2" external diameter tail pipe, this silencer uses a 4" x 380 mm. outside Stainless tube.
* Please note that decibel killer model EXDK-0003 is compatible but not included with this exhaust system. Please add EXDK-0003 to your cart if you wish it to be included in your order.
TYGA no: EXSL-0079
SKU: hon-11010 Categories: ALL products, exhaust system replacement parts, Exhaust systems, Exhausts, Honda, Shop, VFR750F Gen 4, 94-97Front Fender black, Honda MSX125 GROM
€88.02
Front Fender, Asteroid Black Metallic, MSX125 Grom
TYGA no: 61100-K26-900ZD
SKU: MSX-10097 Categories: ALL products, Honda, MSX125 2013 - 2015, OEM parts, ShopTube, Carbon, Oval, 76mm x 99.5mm x 400mm
€124.48
Made from high TG resin and 2/2 weave twill carbon cloth, this replacement tube is suitable for the following TYGA Performance exhaust silencers. It is also suitable for other manufacturerssilencers of the same dimensions. See below for exact specifications
Carbon exhaust guard TYGA, Yamaha R25 – R3
€63.97
Exhaust Guard, TYGA Slip On, Yamaha R25/R3
Made from specially formulated high temperature resin, this exhaust guard adds the finishing touches to the TYGA Performance slip-on exhaust transformation. Fits in minutes and adds a factory GP touch to your bike.
Note, this product is only suitable when used with TYGA Performance R25 and R3 slip-on exhaust systems EXPS-0059 and EXPS-0060