Tyga Step Kit Replacement Gear Shaft Clamp, NSR250
€9.34
Tyga Step Kit Replacement Gear Shaft Clamp, NSR250
Seat cowling (grp) stock shape, Honda NSR250 MC21
€234.42
This seat cowling is designed for the classic racers out there or competing in classes where you need to keep the stock silhouette. It is a full-on race version with the seat area covered over for maximum rider feedback when on the limit. only available as race version, no street version with light provision.
TYGA no: BPFT-0001
SKU: hon-10444 Categories: ALL products, Bodykit replacement parts, Bodywork, Bodywork and carbon, Honda, NSR250 MC21, ShopFront fender RVF, NC35
€66.24
Same shape as original
Compatible Parts:
All Tyga Performance and Honda OEM panels.
TYGA no: BPFF-0004
SKU: hon-10125 Categories: ALL products, Bodywork, Bodywork and carbon, Bodywork and carbon, Honda, RVF400RR NC35, ShopUpper Stay, TYGA Eyes, KTM RC125/200/250/390
€214.08
Upper Stay, TYGA Eyes, KTM RC125/200/250/390
Replacement upper stay should be used on Upper Cowling, KTM RC Series BPFU-7231(p) and BPCU-7231(p)
TYGA no: TYLY-0172
SKU: ktm-10103 Categories: ALL products, Bodykit replacement parts, Bodykit replacement parts, Bodywork, Bodywork and carbon, Bodywork and carbon, RC 125/200, RC 390Top end rebuild set Cylinder B, Honda NSR250 MC21/MC28
€293.88
The picture shows everything you need to do a top end rebuild on your MC21/28. One kit includes all parts for one cylinder (cylinder ‘B’). To overhaul both cylinders please order 2 kits.
Honda OEM:
1x Gasket cylinder 12192-KV3-680
1x Gasket head 12251-KV3-830
1x Piston ring 13010-KV3-305
1x Piston no mark 13102-KV3-830
1x Piston pin 13111-KV3-771
1x RC valve shaft E clip 90601-KV3-000
1x Bearing piston 91102-KV3-771
1x Seal, RC valve shaft 91201-PA9-004
2x Dowel cylinder 94301-10160
2x Piston Circlip 15mm 94601-15000
There are different kits depending on the piston supplied and the pistons are sized to match the cylinder. The cylinders have a letter stamped on them. A cylinder = B piston B cylinder = no mark piston, C cylinder = D piston. The largest cylinder bore is A and the smallest is C. However, note that this is only for when cylinders are new or in good condition, so if the cylinder is worn, the corresponding piston will be a looser so a bigger piston might be advised. If the cross hatch honing of the cylinder is very feint then we suggest using the next size up piston. The differences in sizes are tiny (11 microns between largest and smallest) and for the most part not an issue so it is not a problem if a smaller piston is used in a larger cylinder or the other way round.
Cylinder A = 54.008mm – 54.011mm use Piston B = 53.966mm – 53.969mm
Cylinder B = 54.004mm – 54.008mm use Piston # = 53.962mm – 53.965mm
Cylinder C = 54.000mm – 54.004mm use Piston D = 53.958mm – 53.961mm
Piston to bore clearance = 0.039mm – 0.045mm
TYGA no: NHPS-0001B
SKU: hon-10440 Categories: ALL products, High performance, High performance, High performance, Honda, NSR250 MC21, NSR250 MC28, ShopFront fender (GRP), HRC NSR250 replica
€75.27
Front Fender, GRP, HRC NSR250 replica
Front Fender, Factory HRC NSR250 Racer Style. This front fender is designed to fit HRC factory NSR250 forks but could possibly made to fit other models with suitable mounting hardware. It is similar in styling to the front fenders used by factory riders such as Cadalora, Biaggi, Ukawa, Okada etc. in the years 1992-1995. The reason for this fender being in our line up is we were lucky enough to source some factory forks and needed a fender to go with them and wanted something as close the original as possible and designed it from photos and memory so while similar, it is not an exact replica. In any case if you look at the fenders used by HRC at that time, you can see that there are slight differences between years and bikes.
We don’t know if it will fit any other models but we know it does not fit any other front ends that we have tested it on such as NX5, RVF400, NSR50 MC18/21/28 etc.
TYGA no: BPFF-0007
SKU: hon-10942 Categories: ALL products, Bodywork and carbon, CNC parts, Honda, RS250R NF5 / NX5, ShopSection Final shorty stainless, Honda Monkey 125 2018-
€109.84
Set, Full System, Monkey 125 (No Silencer)
Can be used with TYGA Moto Maggot Silencer EXSL-8213(p)
See also EXPS-0104 For complete set
Screen clear stock shape, Honda VFR750 RC30
€52.00
Upper cowling “stock”, Honda VFR750 RC30 (hon-10569)
Direct replacement for OEM Honda lower cowling with headlight and indicator holes filled in. Due to being constructed with strong flexible epoxy resin, it is thinner and therefore about 65% the weight of the stock upper cowling. In every other way, the same as stock. Can be used with TYGA Performance or factory Honda RC30 lower cowlings.