Silencer stainless round, WSS300 (street) system, KTM RC390
€406.03
Set pipe Full race system WSS300 (race), KTM RC390
This full exhaust system has been conceived to meet WSS300 specifications and carefully designed to squeeze the most power out of the 390. The stainless steel headers are tapered and the sections hand- rolled and welded to give this system incredible looks as well as performance.
And with full spring mounting, fitting and removal of the exhaust is quick and simple. Ideal in a race environment.
By taking advantage of better routing under the engine, the exhaust can be made to optimize dimensions to exploit the motor’s full potential. In addition, by tucking it up through the swing arm, the exhaust does not have any clearance issues in tight bends and is kept away from side which is the most vulnerable position in the case of an accident, increasing its survivability.
The system features a primary silencer, which helps reduce the sound level without any loss of performance.
The system is also provided with a dB killer as well as a carbon heat shield and a bracket so you can mount this system on the earlier RC390 models which did not have this already on the frame, meaning this exhaust will fit all RC390 models to date.
Sound test of the full TYGA system back to back with the Akrapovic World Supersport 300 titanium pipe.
As you can see on the chart below, the sound levels (without DK) are pretty much identical between the two systems. The DK knocks about 5 decibels off everywhere.
Due to the new routing of the exhaust, it is necessary to re-route the water hoses and remove the thermostat, and we provide all the necessary hoses for this conversion. Also, due the exhaust running under the engine, the stock belly pan is not compatible and we provide some alternatives which are not included in the cost of the exhaust.
Note, this is what we describe as the ‘Street’ system. The only difference between this and the race one is the silencer is in a more out board position to clear license/Registration place when used on the street. Powerwise, it is identical to EXPS-0112
TYGA no: EXSL-0074
SKU: ktm-10149 Categories: ALL products, Exhausts, Exhausts, KTM, RC 390, Stock list, all modelsExhaustset stainless steel carbon silencer round, Honda CBR125
€479.79
This full race system has been specifically designed for the CBR125 to maximise power. Made in stainless steel with spring mounted carbon silencer this system significantly increases performance, saves weight and enhances the looks of the bike. Sounds great too!
TYGA no: EXPS-0006
SKU: hon-10277 Categories: 4 stroke exhaust sets, ALL products, CBR125R/CBR150R 2004-10, Exhausts, Honda, ShopRacing stepkit black/BLUE adjustable, Honda Monkey 2018
€477.27 €395.87
Racing Rear Set Kit, Adjustable, Black, Monkey 125
With all major components designed specifically for the Monkey 125 in mind, this rear set kit is the best on the market. Designed in-house by TYGA Performance using the latest CAD/CAM software, these tough CNC machine-made step kits are made from top quality, aircraft grade aluminium and utilise TYGA’s unique and elegant system to provide ten different foot peg positions. The kit features levers moving on ball bearings to give precise and smooth movement. In addition to the technical specifications, emphasis has also been given to make the steps as uncluttered as possible with the rear master cylinder hidden from view and no unsightly unused holes on view etc. The kit comes complete, ready to bolt on with stainless steel fasteners, new OEM Honda axle bolt and carbon heel guards. With individualism in mind, there is a choice of ten colour combinations available and all components are available as replacement or separate items.
Notes:
No real brake light provision. If required, we recommend installation of inline pressure switch.
Fitting this rear set requires replacing the axle bolt with a slightly longer one, a new orginal OEM honda axle bolt is included
This rear set cannot be used in a reverse (GP) shift pattern
TYGA no: STAA-1027BLUE
SKU: msx-10421 Categories: ALL products, CNC parts, Honda, Monkey 125 2018-, ShopExhaustset race Stainless steel carbon Silencer round, NC30 NC35
€1,155.40
Exhaustset race Stainless steel no Silencer, NC30 NC35
The TYGA Full Race System has been designed with maximum power mind. This system is a necessity if you need to squeeze every drop of horse power from the machine.
Manufactured from TIG welded stainless steel sections throughout, with all joints secured by springs, for that ‘factory’ look and feel. The system fits both the NC30 and NC35. Most systems are not designed to be used with a side stand on the NC30, but the TYGA system can be used with a side stand on both the NC30 and NC35.
For unsurpassed looks, sound and performance, this system can be used with any of our 400 system exhaust silencers.
If you need further reason to purchase this product, this exhaust is considerably lighter than the stock system. Weighing only half the weight of the stock system makes for a weight saving of4.2 kg.
NC35:
First, an NC35 was tested with the original Honda exhaust system and produced a peak of 53.5hp; about the right number for a stock bike.
Then the pipe was changed for the TYGA full stainless system, and the main jets increased one size from stock front and rear. No other changes were made, and the peak hp increased to 59.9hp, a gain of 6.4hp (Over 8% more power!)
NC30:
On the NC30, the advantage over the stock exhaust system is higher. With just the TYGA pipe and a couple of main jet changes, the power leaps from a stock 52hp up to a healthy 59hp. That’s 7hp, or 13.5% more.
The pipe set can be used with any silencer with a2 inch internal diameter bore which is held in place by springs for ease of fitment and removal. TYGA provide the following compatible silencers which can either be ordered separately with this system or together as a set.
For unsurpassed looks, sound and performance, this system is supplied with silencer EXSL-0012.
This system may not comply to specific country noise emission regulations and is not homologated for street use.
TYGA no: EXPS-0010
SKU: hon-10103 Categories: 4 stroke exhaust sets, ALL products, Exhausts, Exhausts, Exhausts, Honda, RVF400RR NC35, Shop, VFR400RR NC30Carbon Rear hugger, Suzuki RGV 250
€208.50
Rear Hugger (Carbon), VJ22 RGV250
This product is designed to fit both the braced and ‘banana’ arm model VJ22 RV250
Let your bike stand out from the crowd with this beautiful carbon fibre product.
TYGA no: BPCH-9008
SKU: suz-10017 Categories: ALL products, Bodywork and carbon, Bodywork and carbon, Carbon, RGV250 VJ22, Shop, SuzukiSection, Pipe, Underbelly, Full Race System, MSX125 Grom
€150.88
Section, Pipe, Underbelly, Full Race System, MSX125 Grom
Suitable for our exhaust systems EXPS-0064 and EXPS-0068
Bush 3rd & 4Th driven gear no.22, RGV250/RS250
€30.89
VHM insert, Aprilia RS125 (alg-10176)
piston height -0.35 mm, squish 0.90 mm. Most used is 12,0 cc.
VHM are a respected manufacturer of high quality racing parts used by factory teams world wide.
We are pleased that we can offer VHM products on our website.
The VHM cylinder head is designed with central spark plug position for superior burn, and removable combustion chamber inserts so that changes of compression ratios are quick and simple, and no more wasted head gaskets thanks to the O-ring design
This VHM head set uses the standard water hose spigots. The standard spark plugs may be used.
Detailed instruction on the setting up of VHM heads can be found on their website at www.vhm.nl
TYGA / Kitaco Power up kit maggot , Honda MSX125 GROM
€702.49 €632.24
TYGA/KITACO Power Up Kit, Maggot Type
This power up kit is designed to give a significant power boost over stock. Using TYGA Performance and KITACO products, the power of the MSX125 Grom is increased by 25%. Below is the dyno graph. STD vs our full system with carbon silencer, Kitaco type 2 camshaft, i-map (setting #3). Similar results were found with the Moto Maggot and stainess type silencers.
Parts
This product consists of the components shown below, namely:
EXPS-0042 Set, Pipe, Full Race System, MSX125 Grom, Mot Maggot
KIT-300-1432010 KITACO Type 2 Camshaft
KIT-763-1432010 KITACO i-Map. Fuel Injection Controller
Option:
KIT-763-0500900 i-Map interface cable. To adjust the i-map for special setting. Software available on KITACO website.
For those who want a Type 1 camshaft, please put this in the commentbox at check out.
Description:
Fitting this Power Up Kit to your Honda MSX125/GROM gives a significant increase in top end performance and over rev. Peak hp is moved from 7,000rpm (std) up to 8,000rpm, with a 1.6hp gain at peak.
Fitting the i-Map Fuel Injection Controller is a necessary modification to avoid the engine running lean and being damaged. Running the KITACO Type 2 camshaft without the i-Map is NOT an option!
The wire harness requires modification and the documents are included with the kit, or can be viewed here: http://www.kitaco.co.jp/data/product/link/instaling_manual/kitaco_installing_manual_grom_imap.html
The i-Map is shipped with “setting #3” activated. This is the basic map for this kit, but the map can be modified using the optional i-Map interface cable and software downloadable from the KITACO website:
i-Map Fuel Manager: http://www.kitaco.co.jp/dlservice.html
TYGA no: TPER-0097
SKU: MSX-10306 Categories: ALL products, Exhausts, Exhausts, High performance, High performance, Honda, MSX125 2013 - 2015, MSX125SF 2016 -2020, Shop