Cover, Meter, Ninja 250R 2008 -12
€40.82
Cover, Meter, Ninja 250R 2008 -12
TYGA no: 14091-0722
SKU: kaw-10221 Categories: ALL products, Kawasaki, Kawasaki OEM parts, Ninja 250R 2008- 12, ShopFront Fork Preload Adjusters (Pair), ninja 400
€200.55
Front Fork Preload Adjusters, Pair, Ninja 400
These fully functional preload adjusters replace the blank end caps on the stock Ninja 400 front suspension. These caps allow the rider to increase the amount of preload on the internal springs, allowing for a better set up for your riding style or conditions. Essential for spirited riding through the twisties or track days and racing.
This modification allows preload to be increased from the stock setting by 12mm. The minimum setting gives the same preload as stock.
Supplied in red and blue anodised finish, these adjusters are as beautiful as they are functional.
TYGA no: TYLY-0099k
SKU: kaw-10100 Categories: ALL products, Exhausts, Kawasaki, Ninja 400R 2018-, Various partsSet full race system high level with carbon silencer with carbon cap, Honda MSX125SF GROM
€519.40
Set, Pipe, Full Race System, High Level, MSX125SF Grom, Carbon Oval/Carbon End Cap. Second Generation.
This full race system has been specifically designed for the MSX125 to maximise power. Made in stainless steel with spring mounted carbon silencer this system increases performance, saves weight and enhances the looks of the bike. Sounds great too!
Total weight of the set is 2100 grams
Performance and Dynograph
The blue trace shows the 100% standard Honda MSX125 Grom, compared to the red trace, which is after installing the TYGA Full System set (EXPS-0043)
A useful gain all through the range, increasing as the revs rise up to maximum.
Similar Products:
Please also see:
EXPS-0065 Moto Maggot High level System for 2016 MSX125SF second generation Grom
EXPS-0067 Stainless Oval High level System for 2016 MSX125SF second generation Grom
Note: Some modification of the stock Honda rear hugger (no modification required if using the hugger BPCH-7028 and BPCH-7128) and stock Honda rear fender is necessary to install this system
Note, please check compatibility of under cowl/belly pan with exhaust before ordering. Our products are designed to fit the widest range of products and models but in some cases TYGA products made for the first generation MSX125 Grom are not compatible with the second generation. Please refer to table before ordering.
TYGA no: EXPS-0066
SKU: MSX-10339 Categories: ALL products, Exhausts, Honda, MSX125SF 2016 -2020, ShopCollar, Manifold, NC30/35
€17.74
Manifold Collar. Fitted to rear cylinder port. For use with:
EXPS-0002 Set, Pipe, Full Race System NC30-35 (No Silencer)
EXPS-0011 Set, Pipe, Full Race System NC30-35 Maggot Silencer
EXPS-0028 Set, Pipe, Full Race System NC30-35, Oval Carbon/Carbon End Cap Silencer
EXPS-0012 Set, Pipe, Full Race System NC30-35, Oval Stainless Silencer
EXPS-0053 Set, Pipe, Full Race System NC30-35, Round Aluminium Silencer
EXPS-0010 Set, Pipe, Full Race System NC30-35, Round Carbon Silencer
EXPS-0026 Set, Pipe, Full Race System NC30-35. Round Carbon/Carbon End Cap Silencer
EXPS-0003 Set, Pipe, Twin Stack System, Carbon Silencers
EXPS-0005 Set, Pipe, Twin Stack System, Stainless Silencers
TYGA no: EXMN-0008
SKU: hon-10855 Categories: ALL products, Exhausts, Exhausts, Exhausts, Stock list, all modelsThrottle Cable A, MC28
€63.60
Throttle Cable A, MC28
TYGA no: 17910-KV3-950
SKU: hon-11165 Categories: ALL products, Honda, Honda OEM products, New OEM Honda parts, NSR250, NSR250 MC28Castle nut tool, Honda MC21 NC30 NC35
€30.04
Tool to loosen/tighten the castle lock nut that secures the swingarm adjuster bolt on the NSR250 MC21. Also used for the castle locknuts on the adjusters that hold the NC30/35 engine in position. No more need for a hammer and drift, do the job properly!
Does not fit the swing arm lock nut on MC28 or NC30/35
TYGA no: TYTO-0008
SKU: hon-10521 Categories: ALL products, Honda, NSR250 MC21, RVF400RR NC35, Shop, Universal parts, Various parts, Various parts, Various parts, VFR400RR NC30Carbon Air duct “satin” (pair), NC35
€308.36
These real carbon air ducts are a direct replacement for the cheap and nasty plastic ones the bike is supplied with. Fits in a few minutes and makes a dramatic improvement to the overall appearance of the bike.
TYGA no: BPCX-0018satin
SKU: hon-11444 Categories: ALL products, Bodywork and carbon, Carbon, Honda, RVF400RR NC35, ShopSeat cowling carbon, Honda NSR250 MC28
€827.70
Seat Cowling, (Carbon), MC28 GP-T
We now make four versions of our NSR250 GP Race seat cowling for use for the MC28 in 8 different race and street sets. This product includes ONLY the seat cowling for replacement in the event of an accident or can be used for a project bike of another model. For the MC28, we recommend ordering one of the complete kits below (BPFS-****) which includes all the necessay parts to complete the modification. For installation of any other model the customer will need to make the necessary modifications,
BPFS-0133 (GRP,Street)
BPFS-0134 (GRP Race)
BPFS-0135 (Carbon,Street)
BPFS-0136 (Carbon, Race)
The advantages of this seat cowling over stock include:
– use with rest of seat cowlign kit, much lighter than stock
– new design allows for integrated LED Tail light ( BPLT-0008) for flush fitment and new lighter registration/license plate holder ( BPFX-9006). For race use, location for LED Tail light acts as air vent
– higher at the rear, to give the bike a more agressive stance
– better rider control by use of enclosed seat area
– improved strength with precision in design and fitment
Tyga Performance Compatible Parts for this Product:
This product is compatible with:
BPFX-9033, BPFX-9333, BPCX-9033 and BPCX-9333 Undertray, NSR250 GP-T
TYLY-0108 Subframe, NSR250 GP-T
BPFX-9233 Seat Support, NSR250 GP-T
BPSP-0006 Seat Pad, GP-T
BPAC-0001 Rear Brake Reservoir Kit,
BPLT-0009 LED Taillight
BPFX-9133 Registration Plate Holder GP-T
TYGA no: BPCT-9133Â
SKU: hon-10464 Categories: ALL products, Bodykit replacement parts, Bodywork, Bodywork and carbon, NSR250 MC28, Shop