Oops this is 404! Let's help you find what you were looking for...

Tyga Europe Performance Parts provides a wide range of motorparts for your bike! 

Section header #3-4 stainless, Kawasaki ZXR400L

234.71

(284.00 inc. VAT )

Section, Header, #3-4, Stainless, ZXR400L

Header section, Cylinder 3-4, used on TYGA-Performance Kawasaki Exhaust Systems:

EXPS-0137
EXPS-0138
EXPS-0139
EXPS-0140

TYGA no: EXPT-3443

SKU: kaw-10240 Categories: , ,
Read more

Carbon rear hugger TYGA, Honda MSX125 Grom 1st + 2nd gen.

249.58

(301.99 inc. VAT )

Rear Hugger, (Carbon) TYGA Style. MSX125 Grom. Includes integrated chain guard and replaces the stock plastic part. Easy to install, lighter and looks way, way, cooler!

Read more

Crankshaft Bearing, A, NSR250 MC18/21/28

106.55

(128.93 inc. VAT )

Crankshaft Bearing, Left, NSR250 MC21/28

Genuine OEM KOYO main crankshaft bearing for your Honda NSR250 MC21/28.

See also TYPP-0012SET for set consisting of one each of the left, centre and right crank bearings.

Read more

Carb Service Kit A, 28 pieces, Suzuki GSXR750-M

55.41

(67.05 inc. VAT )

Carb Service Kit A, 28 pieces, Suzuki GSXR750-M

LiteTek Carburettor Seal Kit to suit: Suzuki GSXR750-M (1991)
Made from long lasting, ethanol resistant elastomers and Viton®

Consist of the following items:

4x FB-008 Float Bowl Ring, Material: Flourosilicone (OE part number: 123258-44B00)
4x OR-005 Pilot Screw O-Ring, Material: Viton 70A (OE part number: 13295-29900)
4x WS-001 Pilot Screw Washer, Material: Stainless Steel (OE part number: 13291-29900)
4x OR-026 Top Cap O-Ring, Material Viton 65 (OE part number: 13278-02340)
4x OR-010 Float Mount O-Ring, Material: Viton 70A (OE part number: 13374-44030 superseeded by 13374-35C00)
4x OR-031 Float Assy O-Ring O-Ring (OE part number: 13374-46710)
4x OR-018 Side Housing O-Ring, Material: Viton70 A (OE part number: 13278-47090)

TYGA no: CKA-Suzuki-GSXR750-M

SKU: alg-10343 Categories: , ,
Read more

Tank Filler Cap Breather Rubber, MC28

11.45

(13.85 inc. VAT )

Tank Filler Cap Breather Rubber, MC28

TYGA no: 17646-MN8-700

SKU: hon-11167 Categories: , , , , ,
Read more

Top end rebuild set Cylinder C, Honda NSR250 MC21/MC28

293.88

(355.59 inc. VAT )

The picture shows everything you need to do a top end rebuild on your MC21/28. One kit includes all parts for one cylinder (cylinder ‘C’). To overhaul both cylinders please order 2 kits.

Honda OEM:

1x Gasket cylinder 12192-KV3-680

1x Gasket head 12251-KV3-830

1x Piston ring 13010-KV3-305

1x Piston D mark 13102-KV3-830

1x Piston pin 13111-KV3-771

1x RC valve shaft E clip 90601-KV3-000

1x Bearing piston 91102-KV3-771

1x Seal, RC valve shaft 91201-PA9-004

2x Dowel cylinder 94301-10160

2x Piston Circlip 15mm 94601-15000

There are different kits depending on the piston supplied and the pistons are sized to match the cylinder. The cylinders have a letter stamped on them. A cylinder = B piston B cylinder = no mark piston, C cylinder = D piston. The largest cylinder bore is A and the smallest is C. However, note that this is only for when cylinders are new or in good condition, so if the cylinder is worn, the corresponding piston will be a looser so a bigger piston might be advised. If the cross hatch honing of the cylinder is very feint then we suggest using the next size up piston. The differences in sizes are tiny (11 microns between largest and smallest) and for the most part not an issue so it is not a problem if a smaller piston is used in a larger cylinder or the other way round.

Cylinder A = 54.008mm – 54.011mm use Piston B = 53.966mm – 53.969mm

Cylinder B = 54.004mm – 54.008mm use Piston # = 53.962mm – 53.965mm

Cylinder C = 54.000mm – 54.004mm use Piston D = 53.958mm – 53.961mm

Piston to bore clearance = 0.039mm – 0.045mm

TYGA no: NHPS-0001C

SKU: hon-10441 Categories: , , , , , , ,
Read more

Seat cowling (GRP), stock shape street, Honda VFR750 RC30

386.36

(467.50 inc. VAT )

Upper cowling “stock”, Honda VFR750 RC30 (hon-10569)

Direct replacement for OEM Honda lower cowling with headlight and indicator holes filled in. Due to being constructed with strong flexible epoxy resin, it is thinner and therefore about 65% the weight of the stock upper cowling. In every other way, the same as stock. Can be used with TYGA Performance or factory Honda RC30 lower cowlings.

TYGA no: BPFT-0011

SKU: hon-11416 Categories: , , , ,
Read more