Carbon generator/sprocket cover, Honda NSR250 MC18/MC21/MC28
€220.36
Generator/Front Sprocket Cover NSR250
This lightweight carbon component will make your engine look like it belongs in the GP paddock!Complete with all mounting holes to install speedometer drive and cable guide for side stand switch.
Important, this products re-uses the stock engine case guard from the plastic cover.
TYGA no: BPCC-9106
SKU: hon-10471 Categories: ALL products, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Carbon, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, ShopCarbon meter cover black, MC18/NC23/NC30
€42.01
Attractive carbon cover for NC30 meter assembly.
For fitment, simply remove adhesive backing and pop it on over the three foam retaining buttons.
Fits Honda models as follows: MC18 NSR250, NC23 CBR400-RR, NC30 VFR400R. (Not MC19)
TYGA no: BPCC-0006
SKU: alg-10057 Categories: ALL products, Bodywork and carbon, Carbon, CBR400RR NC23, Honda, NSR250 MC18, Shop, Various parts, Various parts, VFR400RR NC30Section header stainless WSS300 race system, KTM RC390
€226.68
Set pipe Full race system WSS300 (race), KTM RC390
This full exhaust system has been conceived to meet WSS300 specifications and carefully designed to squeeze the most power out of the 390. The stainless steel headers are tapered and the sections hand- rolled and welded to give this system incredible looks as well as performance.
And with full spring mounting, fitting and removal of the exhaust is quick and simple. Ideal in a race environment.
By taking advantage of better routing under the engine, the exhaust can be made to optimize dimensions to exploit the motor’s full potential. In addition, by tucking it up through the swing arm, the exhaust does not have any clearance issues in tight bends and is kept away from side which is the most vulnerable position in the case of an accident, increasing its survivability.
The system features a primary silencer, which helps reduce the sound level without any loss of performance.
The system is also provided with a dB killer as well as a carbon heat shield and a bracket so you can mount this system on the earlier RC390 models which did not have this already on the frame, meaning this exhaust will fit all RC390 models to date.
Sound test of the full TYGA system back to back with the Akrapovic World Supersport 300 titanium pipe.
As you can see on the chart below, the sound levels (without DK) are pretty much identical between the two systems. The DK knocks about 5 decibels off everywhere.
Due to the new routing of the exhaust, it is necessary to re-route the water hoses and remove the thermostat, and we provide all the necessary hoses for this conversion. Also, due the exhaust running under the engine, the stock belly pan is not compatible and we provide some alternatives which are not included in the cost of the exhaust.
Note, this is what we describe as the ‘Street’ system. The only difference between this and the race one is the silencer is in a more out board position to clear license/Registration place when used on the street. Powerwise, it is identical to EXPS-0112
TYGA no: EXPT-0077
SKU: ktm-10135 Categories: ALL products, Exhausts, Exhausts, KTM, RC 390, Stock list, all modelsSeat Bum clamp ( replica), RC30
€32.23
TYGA no: BPCP-0012C
SKU: hon-11535 Categories: ALL products, Honda, RC36-2 -> RC30 replica products, Shop, Stocklist, VFR750R RC30Fuel Tank, GRP, HONDA VFR750R RC30
€977.66
Upper cowling “stock”, Honda VFR750 RC30 (hon-10569)
Direct replacement for OEM Honda lower cowling with headlight and indicator holes filled in. Due to being constructed with strong flexible epoxy resin, it is thinner and therefore about 65% the weight of the stock upper cowling. In every other way, the same as stock. Can be used with TYGA Performance or factory Honda RC30 lower cowlings.
Lower cowling GP-T, Honda NSR250 MC21/MC28
€183.50
Lower Cowling (GRP), MC21, MC28, GP-T, Assy.
This product is designed to be used with BPFU-9033 as part of the Bodywork set BPFS-0137
.
Designed in-house by TYGA Perforance and using 15 years experience of developing fairings for the NSR250, this fairing is lightest and most stylish yet. The design allows for the extra width of an HRC radiator while at the same gives maximum clearance with the track at high angles of lean. Other features include a vent underneath and high quality lamination by our skilled craftsmen. Weight is under 1 kg but strength retained using high strength epoxy resins and good design. See also carbon version BPCL-9033.
It is supplied with spacers to place between fairing and rear lower mounts to ensure clearance with exhaust chambers.
Compatible products:
This product must be used with BPFU-9033
This lower cowling is designed to be used with stock or race exhaust systems though some spacing may be necessary to get clearance with chambers:
1. stock systems, fit with no spacing but will need a small part of the indent on the lower vent removed to clear the chamber. We can modify the lower to fit the stock chambers if requested
2. Tyga chambers require some spacing but no cutting. On some systems (particularly MC28) no spacing is necessary
3. Other systems, can not advise, but should require only spacing or possibly cutting of front of lower where front cylinder header exits.
TYGA no: BPFL-9033
SKU: hon-10532 Categories: ALL products, Bodykit replacement parts, Bodykit replacement parts, Bodywork, Bodywork and carbon, Bodywork and carbon, Honda, NSR250, NSR250 MC21, NSR250 MC28, ShopCarbon set, Suzuki GSX 1000 K7-K8
€387.60
Front fender
Rear Hugger
Chain guard
Direct replacement of the original Suzuki part
Buy a complete set and it saves you money.
Let your bike stand out from the crowd with these beautiful carbon fibre products.
PLEASE NOTE: all ” TYGA” logo stickers on the carbon products can be easily removed because it is applied last above the clearcoat finish.
Top Triple Clamp Nut (M24 x1), Honda MSX125 GROM
€25.75 – €25.76
Top clamp nut in colour. Light weight and good looking. Anodised for a long lasting finish. available in a variety of other colours. See photos.
This nut is a direct replacement to the top nut on many Honda machines, such as MSX125, MC18~28, RVF400, NSR150SP, CBR250/400/500, CBR900. (not suitable for NC30, RC30, SP2 but fits SP1)
The thread is M24x1
Torque setting: 65Nm
TYGA no: H136-A8Z1-0193GOLD-
SKU: msx-10203- Categories: ALL products, CNC parts, CNC parts, CNC parts, Honda, MSX125 2013 - 2015, MSX125SF 2016 -2020