Set pipe, Full race with maggot silencer NEW, Kawasaki ZXR250 2013 –
€519.40
2013-2017, Set, Pipe, Full Race System, Ninja 250R, Moto Maggot Silencer
We now have a new and improved design to give you the edge in this highly competitive class. Through our continuous R&D, we have enhanced the dimensions of components to squeeze even more power from the Ninja 250 when used with the TYGA system*. Made in stainless steel with spring mounted Moto Maggot silencer this system significantly increases performance, saves weight and enhances the looks of the bike. Sounds great too! Unlike the stock system and most other aftermarket full systems, the TYGA Performance full race system is routed up the right side of the bike for the best possible gas flow and the performance figures support this. Please see below.
(* May not comply with noise regulations for some states and territories and may exceed noise regulations for some circuits)
This system is supplied with an Moto Maggot silencer EXSL-9213
Note, this exhaust system is not suitable for the 2008-12 model. For the 2008-12 model, please see EXPS-0018.
* Please also note that all TYGA-Performance pipe sections and silencers are new for 2017 and thus not compatible with previous 2013-2016 TYGA-Performance Ninja 250 Exhaust pipe sections and silencers.
TYGA no: EXPS-0081
SKU: kaw-10064 Categories: 4 stroke exhaust sets, ALL products, Exhausts, Kawasaki, Ninja 250R/300R 2013 -Set pipe, Full race with round stainless silencer, Kawasaki ZXR250/300 2013 –
€548.01
.Set, Pipe, Full Race System, Ninja 250R/300R, Round Stainless SilencerThis full race system has been specifically designed for the Ninja 250 to maximise power. Made in stainless steel with spring mounted carbon silencer this system significantly increases performance, saves weight and enhances the looks of the bike. Sounds great too! Unlike the stock system and most other aftermarket full systems, the TYGA Performance full race system is routed up the right side of the bike for the best possible gas flow and the performance figures support this. Please see below.(May not comply with noise regulations for some states and territories and may exceed noise regulations for some ciircuits)This system is supplied with a stainless round silencer.<iframe width= 560 height= 315 src= https://www.youtube.com/embed/aFjJq-crAQ8 frameborder= 0 allowfullscreen></iframe>
Please see the two dyno graphs from Kawasaki Racing Australia who independently tested the TYGA system against the stock system and also against a well known competitor. The figures clearly show the advantages of installing a TYGA full race exhaust whether it be for street or for race use.Graph 1 shows 8.5% more power over stock just from installing the TYGA Full systemGraph 2 shows the peaks are very similar but look how the TYGA system has more power everywhere else, up to 10% more power in the important 9,000 to 10,000 range. The Leo Vince exhaust was mapped for 98 octane and the Tyga for 91 which should give an advantage to the Leo.
TYGA no: EXPS-0047
SKU: kaw-10030 Categories: 4 stroke exhaust sets, ALL products, Exhausts, Kawasaki, Ninja 250R/300R 2013 -, ShopCarbon cover set instrument surrounds, Honda
€89.29
Carbon cover set instrument surrounds, Honda
Theses covers fit snuggly over the original plastic Honda gauge covers and adds a sporty appearance. They are also ideal for hiding any ugly scratches or dents that may have occurred over the years. They fit in second and can be held in place with a dab of glue or silicone adhesive. Note, these covers are also available as separate covers.
This product is suitable for the following models:
MC18 NSR250
NC30 VFR400R
RC30 VFR750R
TYGA no: BPCC-0027
SKU: hon-10614 Categories: ALL products, Carbon, CBR400RR NC23, Honda, NSR250 MC18, Shop, Various parts, Various parts, VFR400RR NC30Carbon upper cowling street with air duct, Aprilia RS250 Tyga, assy
€726.62
This upper cowling is to be used in our Aprilia RS-250 kits, BPFS-0100 and BPFS-1100
This product is compatible with lower cowling BPFL-9030 and BPCL-9030. Will not fit stock Aprilia lower cowling
TYGA no: BPCU-9030
SKU: apr-10070 Categories: ALL products, Aprilia, Bodykit replacement parts, Carbon, RS250, ShopTank filler cap “racing” (central fill hole type), KTM 7 hole
€69.87
<p><strong><span>Tank Filler Cap, Keyless, Racing Type, KTM, 7 Hole</span></strong></p>
<p><span>This keyless racing fuel tank filler cap is CNC machined from billet aluminium and anodised black with a laser etched TYGA logo. Designed with finger tabs for easy removal while wearing gloves</span></p>
<p><span>Supplied complete with seals and mounting hardware, it can be installed in minutes.</span></p>
<p><span>This product is suitable for KTM RC series sports bike models (RC125/200/250 and 390)</span></p>
<p><span>Fits all KTM RC models which are using the OEM filler cap with code: 90507008000 (2014-2016) but also may fit on later models using a 7 hole filler cap.</span></p>
<p><span>Suitable for the following models:</span></p>
<p><span>KTM</span></p>
<ul>
<li><span>KTM RC125</span></li>
<li><span>KTM RC200</span></li>
<li><span>KTM RC250</span></li>
<li><span>KTM RC390</span></li>
**** Please check photo 2 ****
</ul>
TYGA no: TYLY-0267
SKU: alg-10395 Categories: ALL products, CNC parts, CNC parts, KTM, RC 125/200, RC 390, Shop, Tank fillers, Various parts, Various partsChain adjuster/rear stand bobbin, Honda CBR500
€254.51
This Chain Adjuster/Rear Stand Bobbin Assy. for the CBR500 enables easy installation of a rear paddock stand for chain maintenance and use of tyre warmers etc. It also replaces the cheesy original chain adjusters allowing for ease of removal and fitment of the rear wheel. Unlike the original ones, which fall in a heap on the ground when you pull the rear wheel shaft out, these precision CNC machined adjusters will stay in place enabling the task to be easily completed by yourself.
Please note the bike is secure with the rear wheel removed, however, do not attempt to move the bike in this state.
Carbon tank cover glue on , Honda MSX125SF GROM
€76.02
Carbon tank cover glue on , Honda MSX125SF GROM
Carbon tank cover. Fits over nasty the plastic stock item and transforms the appearance of your bike. Installs in minutes.
Note, we also offer BPCX-7938 which is a direct replacement for the plastic Honda cover for those people wanting to get their tools out and wishing to make a more permanant transformation.
TYGA no: BPCX-7948
SKU: MSX-10360 Categories: ALL products, Bodywork and carbon, Honda, MSX125 GROM, MSX125SF 2016 -2020, ShopTop triple clamp CNC black RACE, KTM RC390, 2014- 21
€442.15
Set pipe Full race system WSS300 (race), KTM RC390
This full exhaust system has been conceived to meet WSS300 specifications and carefully designed to squeeze the most power out of the 390. The stainless steel headers are tapered and the sections hand- rolled and welded to give this system incredible looks as well as performance.
And with full spring mounting, fitting and removal of the exhaust is quick and simple. Ideal in a race environment.
By taking advantage of better routing under the engine, the exhaust can be made to optimize dimensions to exploit the motor’s full potential. In addition, by tucking it up through the swing arm, the exhaust does not have any clearance issues in tight bends and is kept away from side which is the most vulnerable position in the case of an accident, increasing its survivability.
The system features a primary silencer, which helps reduce the sound level without any loss of performance.
The system is also provided with a dB killer as well as a carbon heat shield and a bracket so you can mount this system on the earlier RC390 models which did not have this already on the frame, meaning this exhaust will fit all RC390 models to date.
Sound test of the full TYGA system back to back with the Akrapovic World Supersport 300 titanium pipe.
As you can see on the chart below, the sound levels (without DK) are pretty much identical between the two systems. The DK knocks about 5 decibels off everywhere.
Due to the new routing of the exhaust, it is necessary to re-route the water hoses and remove the thermostat, and we provide all the necessary hoses for this conversion. Also, due the exhaust running under the engine, the stock belly pan is not compatible and we provide some alternatives which are not included in the cost of the exhaust.
Note, this is what we describe as the ‘Street’ system. The only difference between this and the race one is the silencer is in a more out board position to clear license/Registration place when used on the street. Powerwise, it is identical to EXPS-0112
TYGA no: TYLY-1931
SKU: ktm-10219 Categories: ALL products, CNC parts, CNC parts, Exhausts, KTM, RC 125/200, RC 390, Stock list, all models