2T blank plug, NSR250
€7.37
Replaces the 2T oil injector pump for pre mix use. Secure with liquid gasket such as Three Bond 1104. Must be used with TYLY-0015 Plug holder
Note for blocking the extra 2T feed on later model oil pumps.
On later engines (some MC21 and all MC28, there is an extra oil feed to the cases which can be observed when the oil pump is removed. HRC used to supply a little aluminium plug that you knocked into this extra hole to blank it off. However, that is discontinued so what to do depends on whether the conversion to pre-mix is permanent or not.
If permanant, then we recommend you make sure it’s all clean and degreased, and then fill the hole with epoxy steel. Allow it to cure and it’ll never leak.
If you’re not sure if you’ll ever go back to the oil pump, but would like the option, then we suggest covering the hole with a small thin disc of steel or plastic, and then using a RTV sealant to sort of glue that in place and also block it off. The RTV will stop any leaks, and the small disc will stop any RTV going down the hole. This is then soft enough to be cut away at a later date should you need to.
Compatible products:
TYLY-0015 Plug holder
TYGA no: TYLY-0012
SKU: hon-10388 Categories: ALL products, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, Shop, Various parts, Various parts, Various partsVHM piston (flat top) RS125 NX4 1995-’10 – RS250 NX5/NXA 1993-’10
€137.00
Kit, Fairing Set (GRP), Honda NX5 RS250R (1995 NSR250 Style)
Complete Bodywork kit which consists of the following products:
Upper Cowling Race, (GRP) NX5 RS250R (1995 NSR250 Style) (BPFU-9336)
The upper fairing is modelled off the 1995 NSR250 racer, but will fit any NX5 which has the ram air through the fuel tank system. Made from high quality epoxy resin and 200 gram glass fabric, this product is both light and strong. It will tend to flex and not shatter in the event of an accident and hold up well to minor crashes. It is finished in primer ready for paint. To be used with lower cowling BPFL-9036.
Lower Cowling, (GRP) NX5 RS250R (Late Model Style) (BPFL-9036)
The lower fairing is modelled off the ram air version of the NX5 RS250R but will fit any NX5 which uses a stock upper as far as we can tell. Made from high quality epoxy resin and 200 gram glass fabric, this product is both light and strong. It will tend to flex and not shatter in the event of an accident and hold up well to minor crashes. It is finished in primer ready for paint. To be used with upper cowling BPFU-9036
Seat Cowling Race (GRP) NX5 RS250R (1995 NSR250 Style) (BPFT-9036)
This seat cowling is modelled on the 1995 factory NSR250 racer look as ridden by Ukawa, Okada, Romboni, Jacque etc. and is a direct fit for the NX5. The seat cowling uses a special seat support which bolts to the subframe using existing mounting lugs and the seat cowling is covered underneath for streamlining and protection of the PGM and connectors. It is easy to install and being made from high quality epoxy resins and top quality glass fabric is strong and crash resistant.
Seat Support NX5 RS250R (BPFX-9036)
Screen Clear NX5 RS250R (1995 NSR250 Style) (SCRE-0176)
TYGA no: APHO12521750 + size
SKU: alg-10399 Categories: ALL products, Honda, RS250R NF5 / NX5, Shop, Various parts, VHM productsBattery box GP-T, Honda VFR400/RVF400
€53.68
Battery Box, NC30/35 GP-T, Assy.
Precision laser cut and hand welded, this aluminium battery box is part of our GP-T seat cowl kit. Strap and fastening screws provided
Compatible Parts:
Only to be used with NC30 RC211V seat cowl BPFT-9034 and BPCT-9034, subframe TYLY-0133 used in our seat cowling sets, BPFS-0148, BPFS-0149, BPFS-0150 and BPFS-0151
TYGA no: TYLY-0130
SKU: hon-10595 Categories: ALL products, Bodykit replacement parts, Bodykit replacement parts, Bodywork and carbon, RVF400RR NC35, VFR400RR NC30Set pipe, Full race with round aluminium silencer NEW, Kawasaki ZXR250 2013 –
€557.94
2013-2017, Set, Pipe, Full Race System, Ninja 250R, Round Aluminium Silencer
We now have a new and improved design to give you the edge in this highly competitive class. Through our continuous R&D, we have enhanced the dimensions of components to squeeze even more power from the Ninja 250 when used with the TYGA system*. Made in stainless steel with spring mounted round Aluminium silencer this system significantly increases performance, saves weight and enhances the looks of the bike. Sounds great too! Unlike the stock system and most other aftermarket full systems, the TYGA Performance full race system is routed up the right side of the bike for the best possible gas flow and the performance figures support this. Please see below.
(* May not comply with noise regulations for some states and territories and may exceed noise regulations for some circuits)
This system is supplied with an Round Aluminium silencer EXSL-0040
Note, this exhaust system is not suitable for the 2008-12 model. For the 2008-12 model, please see EXPS-0018.
* Please also note that all TYGA-Performance pipe sections and silencers are new for 2017 and thus not compatible with previous 2013-2016 TYGA-Performance Ninja 250 Exhaust pipe sections and silencers.
Carbon fairing side stay pair, Suzuki RGV250 VJ21/22
€70.24
Fairing Side Stay, Carbon, Set, RGV250 VJ21/VJ22
These fairing stays are direct replacements for the Suzuki OE part number 94522-12C-00-000 on the VJ21 and VJ22 RGV250.
TYGA no: BPCC-0061
SKU: suz-10140 Categories: ALL products, Bodywork and carbon, Bodywork and carbon, RGV250 VJ21, RGV250 VJ22, Shop, Suzuki, Various parts, Various partsHandlebar tube assy, kawasaki ninja 2008 -18
€22.89
Handlebar Tube (Assy), Black. Suitable for both left and right sides for Ninja250R /300R
Comes fitted with plastic bungs in each end.
Power pack Boyesen/airbox/Powervalve, Suzuki RGV250 / Aprilia RS250
€979.92 €892.11
Power pack Boyesen/airbox/Powervalve, Suzuki RGV250 / Aprilia RS250
The perfect set voor that extra power and better throttle response.
Part shown in the picture are all parts that come with the set.
The RS250 has an extra cover for under the tank, this will fit both RS250 types.
RGV250 – picture 1 and 2
RS250 – picture 3 and 4
Airbox:
Our race airbox is inspired by the GP road racing technology, taking advantage of a front air intake and all available space within the engine compartment.
And by using the lower part of the fuel tank as closing to increase the volumetric capacity of which becomes 9.5 lt against 6.2 lt of the standard component ( 53%).
The air intake (Snorkel) is positioned in the front to be able to suck a greater amount of air and with less turbulence than the positioning adopted in origin ( in the back)
Its shape also was designed using the calculation FEM (Finite Element Method) to minimize the load losses and therefore increase performance in the complete range of the RPM.
The kit also includes a carbon cover to be mounted close to the air intake to prevent suction of hot air.
All this is mainly reflected in an increase in engine performance, as shown below on the Dyno graph.
Greater maximum power ( 3 hp *)
Better throttle response
Higher max. RPM ( 500 rpm)
A GP “sound”
Improved access for maintenance
Jets #310 – #320(*)
Also be using Carbon you will have weight reduction of around 50% (465 grams compared to 970 grams OEM).
The filter is washable and gives better performance then original
Powervalves:
et ( 4 pieces), complete CNC billet aluminium, RGV250/RS250 (alg-10123)
This set of Power valves is the latest version, and can be used for your Suzuki RGV250 or Aprilia RS250. Fully tested on Dyno and used on track and street bikes.
The set is made of CNC billet aluminium and is special coated.
No more problems with the “power valve pin” and having to buy new ones every 15.000 km.
And the risk that a broken power valve will ruin your engine!!
Power reeds:
Boyesen Power Reeds use a patented dual-stage fiberglass design for more airflow, more air velocity and more overall power.
TYGA no: power p002
SKU: alg-10242 Categories: ALL products, Aprilia, High performance, High performance, High performance, RGV250 VJ22, RS250, Suzuki RGV250Triple clamp CNC black set, KTM RC125/RC200/RC390
€253.69
Top Triple Clamp Set, CNC Black, KTM RC Series
CNC machined top triple clamp with detachable ignition switch/lock holder for your KTM RC Series motorcycle
Designed and machined in house by TYGA, as a direct replacement for the OEM top triple clamp. FEA tested and developed for increased strength without unnecessarily increased weight.
Crafted from aircraft spec 6061-T6 alloy, the top triple clamp is ready to fit.
The detachable ignition lock holder is positioned to allow use of the steering lock, but can be removed for race use.
Update your bike with this great TYGA performance, KTM power part!!
TYGA no: TYLY-1073
SKU: ktm-10072 Categories: ALL products, CNC parts, CNC parts, CNC parts, KTM, RC 125/200, RC 390, Shop