Big bore kit 300cc wiseco, NSR250 MC18/MC21/MC28
€2,264.37
This 300cc Big Bore Kit is identical to the TPER-0007 300cc Big Bore Kit, but the standard 300cc pistons are replaced with high performance options.
In this case we have forged Wiseco pistons that are lighter and stronger than stock. They use Wiseco rings, clips and pins.
See below for performance details for TPER-0007.
Bore & Stroke is 59mm x 54.5mm giving a total displacement of 298cc.
Parts included in the NSR300 kit.
Cylinder x 2 (includes head studs, RC valve, pulley & nut and washers)
Rear Head x 1
Front Head x 1
Piston x 2
Ring set x 2
Piston Pin x 2
Piston Clip x 4
S/E Bearing x 2
Head gasket x 2
Cylinder gasket x 2
RC Valve cables x 4
Water hose x 1
Exhaust Manifold x 2 (to fit TYGA pipes)
Other information:
There is no problem about the RC valves hitting the piston due to thin cylinder wall thickness. This is not an issue on our kit as it’s using different
cylinders, not modified NSR250. They are genuine OEM Honda cylinders, made and plated in Japan to their typical high quality.
The RC valves are easier to adjust than ever on the 300 kit, as there’s only one adjuster screw to play with, and each cylinder marked at the correct ‘fully open’ position for simple setting.
Exact Jetting requirements for your area and application cannot be provided due to differing atmospheric conditions around the world. However, following are some base settings to work from:
MC21 Std bottom end, Wire splice, TYGA Pipes, Airbox lid mod with filter.
Temp: 29 C
Press: 1015mb
Hum: 65%
Alt: 30m
MJ – #182/#185
JN – Std./Std.
SJ – #38/#38
AS – 1.5 turns out
PwrJ – Std./Std.
Tip: Cooler temps, higher pressure and/or lower humidity require richer jetting. High altitude requires leaner settings. Starting off with rich settings will in the worse case foul a plug. Too lean a setting may destroy the engine.
This jet set-up is for guidance only. TYGA Performance cannot be held responsible for any engine damage incurred due to incorrect settings.
At present, this kit is available by special order. Each kit takes approx. four weeks to prepare.
TYGA no: TPER-3007Â
SKU: hon-10390 Categories: ALL products, High performance, High performance, High performance, High performance, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, ShopUpper cowling GP-T, Honda VFR400/RVF400
€317.01
Upper Cowling Street (GRP), NC30/NC35, GP-T, Assy.
Stylish replacement fairing designed in-house by TYGA Performance to give the NC30 and NC35 a contemporary look. This upper cowling utilizes stylish twin double unit LED headlight units, BPLT-0027. Together with lower cowling BPFL-9034 for NC30 and BPFL-9134 for NC35 and other mounting hardware it comprises sets BPFS-0144 for the NC30 and BPFS-0145 for the NC35.
This cowling is supplied with a plastic bung to mount to the meter stay.
See also BPCU-9034 for carbon version of this product.
Compatible parts:
BPFL-9034 and BPFL-9134 Lower Cowling
TYLY-0138 (NC30) and TYLY-0139 (NC35) Upper Stay
TYLY-0187 (NC30) and TYLY-0188 (NC35) Front Stay
TYLY-0189 (NC30) and TYLY-0190 (NC35) Side Stays
BPLT-0027 Headlight
SCRE-0161 Screen, Clear GP-T, or SCRE-0162 Screen, Tint GP-T
TYGA no: BPFU-9034
SKU: hon-10600 Categories: ALL products, Bodykit replacement parts, Bodykit replacement parts, Bodywork, Bodywork and carbon, Bodywork and carbon, RVF400RR NC35, VFR400RR NC30Dash Indicator Bulb Harness, MC21
€17.20
This product plugs in line with the wiring connector that connects to the main harness from the left hand handlebar switch and allows the turn signal instrument warning light to function properly when LED turn signals and turn signal relay TELC-0002 are installed. Without this harness, the LED turn signals and turn signal instrument warning light will not flash properly. To install simply unplug the connector at the front of the bike near the master stay and install the TYGA mini harness in line.
This will fit the Honda NSR250 MC21 but also may fit other Honda models.
TYGA no: TYWH-0003
SKU: hon-10747 Categories: ALL products, Honda, NSR250, NSR250 MC21, Various partsCarbon tank filler cap cover cover, Suzuki RGV 250
€34.06
Carbon Tank Filler cap Cover. Fits Suzuki RGV250, and other models.
TYGA no: BPCC-0010
SKU: suz-10003 Categories: ALL products, Bodywork and carbon, Carbon, RGV250 VJ21, RGV250 VJ22, Shop, Suzuki, Various parts, Various partsCarbon rear hugger, Honda CBR500
€252.04
This lightweight carbon version of the stock hugger will enhance the beauty of your CBR as well as keep road dirt and water away from the rear shock and linkages. Modelled off the genuine plastic Honda aftermarket part but crafted in high quality carbon this products is suitable for the CBR500R, CB500X and CB500F.
Let your bike stand out from the crowd with this beautiful carbon fibre product.
Licenseplate holder Tyga RGV/RC211V
€55.70
This product holds the registration/license plate for use with our RC211V and RGV seat cowlings. It is supplied with a registration/license plate illumination light for countries where this is a legal requirement.
This product attaches by means of two M5 bolts on an angled back flat plate and could be adapted to be used with other models with a flat undersurface.
TYGA no: BPCX-9007
SKU: alg-10033 Categories: ALL products, Bodykit replacement parts, Bodykit replacement parts, Bodykit replacement parts, Bodywork, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, By model, Honda, RGV250 VJ22, RVF400RR NC35, Shop, Suzuki, VFR400RR NC30Carbon licence plate holder tail tidy, Honda Monkey 125 2018-
€91.30
Registration/License Plate Holder/Tail Tidy, (Carbon), Monkey 125 (2018-)
This trickest Monkey 125 tail tidy in the market, made from lightweight carbon fiber, this replaces the huge heavy one provided by Honda. At least Honda made it easy to remove theirs, and ours is quick and easy to install with no modification of components needed.
TYGA no: BPCK-7142
SKU: msx-10447 Categories: ALL products, Bodywork and carbon, Honda, Monkey 125 2018-, ShopSeat cowling stock race , Suzuki RGV 250
€252.35
Seat Cowling (Race, GRP), VJ22, Stock Shape, Assy.
This seat cowling is modelled from the original stock VJ22 shape and is suitable for all race classes but particularly those where the you need to keep the stock silhouette. It is a full-on race version with the seat area covered over for maximum rider feedback when on the limit.
Note that this panel is designed to make it possible to remove the fuel tank while the seat cowling stays installed. The panel is top quality, being lightweight, flexible and tough. Constructed with epoxy resin and multi layer 200 gram mat; do not confuse this with budget race glass made with polyester and chopped strand just because the price is right!
Only available as race version, no street version with light provision.
TYGA no: BPFT-9226
SKU: suz-10094 Categories: ALL products, Bodykit replacement parts, Bodywork, Bodywork and carbon, RGV250 VJ22, Shop, Suzuki