Set exhaust pipe stainless steel silencer with carbon cap , Yamaha R25/R3
€897.95
Set, Exhaust Pipe, Race System, Yamaha YZF-R25 and YZF-R3, Stainless, Stainless Silencer, Carbon End cap
This race system has been specifically developed for the Yamaha YZF R25 and YZF R3 and has been designed for optimum performance. It uses a stainless oval silencer with carbon end cap to keep sound to a minimum. As well as the improved performance, it saves weight over the stock system and of course, it looks awesome!
Compatiblity
This exhaust can be installed on a bike fitted with the stock or with race bodywork and with or without the passenger pegs installed.
No modification of bodywork is required, however, the emission canister must be relocated using the clamp provided.
Please also see EXPS-0073 EXPS-0074 and EXPS-0075 for similar system.
Performance and Dynograph
Please refer to dynographs
A) All Standard.
The standard exhaust system is replaced with the TYGA system. No modifications to the engine or fuelling were performed. Fitting a fuel controller could further increase the performance gains.
B) Airfilter/Airbox modification.
The standard exhaust system is replaced with the TYGA system. The airbox cover has been removed and a high flow filter fitted. This improves power all through the range. Fitting a fuel controller could further increase the performance gains.
TYGA no: EXPS-0072
SKU: yam-10059 Categories: 4 stroke exhaust sets, ALL products, Exhausts, Yamaha, YZF-R25/R3TYGA flywheel/RC valve remover, Honda NSR125/150/250/300
€135.99
This new, TYGA designed 2 in 1 combination tool is a flywheel puller and RC valve removing tool all in one handy package.
Saves space in your toolbox, and less clutter on the work bench.
How to use:
Familiarise yourself with the parts (see picture).
The tool is delivered ready for use as a flywheel puller. Just screw part D into the crank, then wind the (left hand) threaded main body (part A ) into the flywheel centre and pop the flywheel off by rotating part B clockwise. Part C is not used.
For removing the RC valve shaft remove part B completely and refit from the opposite end, screwing all the way home. Then slide in the part C . Position the tool over the valve shaft and wind part C onto the RC valve shaft (left hand thread). When fully home just rotate part B anti-clockwise to pull out the shaft. The RC valve shaft seal and E-clip will probably be damaged in the process, and should be replaced. Part D is not used.
22mm and 19mm spanners (not supplied) are required for correct operation.
*Note* This tool can be used on the NSR150 to remove the RC valve shaft, but will not fit the flywheel. Please use TYTO-0007 for this job.
TYGA no: TYTO-0014
SKU: hon-10329 Categories: ALL products, Honda, NSR150SP, NSR250 MC18, NSR250 MC21, NSR250 MC28, Shop, Tools, Various parts, Various parts, Various parts, Various partsFrame In-fill panels (pair) GRP, RC36-2 RC30 style
€177.69
Steering Stopper, Honda VFR750R RC36 (94-97)
Steering stopper for race use. Reduces degree of movement in steering. Easy to attach using hole for the horn on the standard lower triple clamp.
TYGA no: BPFC-7049
SKU: hon-11461 Categories: ALL products, Bodywork, Honda, RC36-2 -> RC30 replica products, Shop, StocklistBattery Box Cover , Race, GRP, KTM RC390 WSS300
€77.43
Battery Box Cover, Race, GRP, KTM RC390 WSS300
Replacement Battery Box Cover. WSS300, MUST be used with KTM WSS300 hardware
see also:
BPCX-7631UB (Carbon Unpolished)
BPCX-7631B (Carbon Clearcoated)
Set full race system under belly with short stainless silencer with carbon cap, Honda MSX125 GROM
€480.85
.Set, Pipe, Full System, Underbelly, MSX125 Grom, Carbon Oval/Carbon End Cap, Short
This full race system has been specifically designed for the MSX125 to maximise power. Made in stainless steel with spring mounted carbon silencer this system increases performance, saves weight and enhances the looks of the bike. Sounds great too! ( A db killer is included)
Total weight of the set is 2300 grams
Performance and Dynograph
The blue trace shows the 100% standard Honda MSX125 Grom, compared to the red trace, which is after installing the TYGA Full System set (EXPS-0064) with no other changes to the stock bike.
A useful increase in peak power and further gains could probably be had with remapping etc.
Similar Products:
Please also see:
EXPS-0064 Stainless, Underbelly, with long silencer
<iframe width= 560 height= 315 src= https://www.youtube.com/embed/mSTQKSWArE0 frameborder= 0 allowfullscreen></iframe>
TYGA no: EXPS-0068
SKU: MSX-10348 Categories: ALL products, Exhausts, Exhausts, Exhausts, Honda, MSX125 2013 - 2015, MSX125 2021-, MSX125SF 2016 -2020, ShopExhaustset stainless steel aluminium silencer, Honda CBR300
€411.44
The TYGA Full Race System has been designed with maximum power mind. This system is a necessity if you need to squeeze every drop of horse power from the machine.
Manufactured from TIG welded stainless steel sections throughout, with all joints secured by springs, for that ‘factory’ look and feel. For unsurpassed looks, sound and performance, this system is supplied with silencer EXSL-0040. If you need further reason to purchase this product, this exhaust is considerably lighter than the stock system. Weighing only 3 kg instead of the 8 kg of the stock system
This system may not comply to specific country noise emission regulations and is not homologated for street use. Actually it is extremely loud so be warned!
TYGA no: EXPS-0055Â
SKU: hon-10372 Categories: 4 stroke exhaust sets, ALL products, CBR300R 2014-, Exhausts, Honda, ShopCarbon race airbox lid, Honda NSR250 MC21/MC28
€210.89
The stock airbox is restricted by the size of the inlet holes on the lid which limits the amountof power that can be unleashed from the NSR250. By replacing the stock airbox lid with the TYGA Performance version, the inlet to the airbox is more than doubled in size and the flow improved by having one large trumpet.
This product is a direct replacement for the stock one and uses all the stock hardware. It even has an ‘O’ ring groove so by removal and re-use of the stock airbox lid ‘O’ ring, a perfect seal with the airbox can be retained. A mesh is supplied in the airbox to hold the stock air filter securely in position.
As well as potential power improvements over the stock airbox, there is no denying it certainly looks a lot more trick than the Honda one too!
TYGA no: BPCX-9010
SKU: hon-10323 Categories: ALL products, Carbon, High performance, High performance, Honda, NSR250 MC21, NSR250 MC28, ShopPiston Circlip 15mm, MC16~28
€1.05
Piston Circlip 15mm, MC16~28
TYGA no: 94601-15000
SKU: hon-11096 Categories: ALL products, High performance, Honda, New OEM Honda parts, New OEM Honda parts, New OEM Honda parts, NSR250, NSR250 MC18, NSR250 MC21, NSR250 MC28