RC Valve Flap R., NSR150SP
€40.35
RC Valve Flap R., NSR150SP
TYGA no: 14201-KW6-840
SKU: hon-11190 Categories: ALL products, Honda, Honda OEM products, New OEM Honda parts, NSR150SPBig bore kit 300cc wiseco VHM, NSR250 MC18/MC21/MC28
€2,842.71
Big Bore Kit, NSR300, Wiseco, VHM *
This 300cc Big Bore Kit is identical to the TPER-0007 300cc Big Bore Kit, but the standard 300cc heads and pistons are replaced with high performance options.
In this case we have forged Wiseco pistons that are lighter and stronger than stock, and also changable insert VHM cylinder heads, which have been specifically developed by TYGA and VHM for use with the TYGA 300cc Big Bore Kit.
See below for performance details for TPER-0007.
Bore & Stroke is 59mm x 54.5mm giving a total displacement of 298cc.
Parts included in the NSR300 kit.
Cylinder x 2 (includes head studs, RC valve, pulley & nut and washers)
Rear Head x 1
Front Head x 1
Piston x 2
Ring set x 2
Piston Pin x 2
Piston Clip x 4
S/E Bearing x 2
Head gasket x 2
Cylinder gasket x 2
RC Valve cables x 4
Water hose x 1
Exhaust Manifold x 2 (to fit TYGA pipes)
Other information:
There is no problem about the RC valves hitting the piston due to thin cylinder wall thickness. This is not an issue on our kit as it’s using different
cylinders, not modified NSR250. They are genuine OEM Honda cylinders, made and plated in Japan to their typical high quality.
The RC valves are easier to adjust than ever on the 300 kit, as there’s only one adjuster screw to play with, and each cylinder marked at the correct ‘fully open’ position for simple setting.
Exact Jetting requirements for your area and application cannot be provided due to differing atmospheric conditions around the world. However, following are some base settings to work from:
MC21 Std bottom end, Wire splice, TYGA Pipes, Airbox lid mod with filter.
Temp: 29 C
Press: 1015mb
Hum: 65%
Alt: 30m
MJ – #182/#185
JN – Std./Std.
SJ – #38/#38
AS – 1.5 turns out
PwrJ – Std./Std.
Tip: Cooler temps, higher pressure and/or lower humidity require richer jetting. High altitude requires leaner settings. Starting off with rich settings will in the worse case foul a plug. Too lean a setting may destroy the engine.
This jet set-up is for guidance only. TYGA Performance cannot be held responsible for any engine damage incurred due to incorrect settings.
At present, this kit is available by special order. Each kit takes approx. four weeks to prepare.
TYGA no: TPER-1007
SKU: hon-10391 Categories: ALL products, High performance, High performance, High performance, High performance, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, ShopSeat set RCV211 with carbon, NC30 assy
€457.28
This is the seat cowling with carbon as used in the NC30 RC211V style seat cowling kit, BPFS-0027.
This product is suitable as a replacement seat cowling in the event of damage to the one in the set. It is also ideal for somebody wishing to custom fit it to another model. Please note it will need modifying to fit anything other than the NC30.
To be used with:
subframe TYLY-0025
battery box TYLY-0026
taillight BPLT-0013
registration/license plate holder BPCX-9007
TYGA no: BPCT-9017
SKU: hon-10089 Categories: ALL products, Bodywork, Bodywork and carbon, Honda, Shop, VFR400RR NC30Airbox carbon, A kit, Honda RS250 NX5
€673.59
Airbox, Carbon/Kevlar, NSR250 MC21/MC28
This high quality carbon/Kevlar air box is an adaptation of the HRC air box and has the following features.
Maximum volume, more than double the size of the stock air box for better flow and power
High flow, large area foam filter for street use
Snug fitting rubber base to prevent leaks around carb insulators
Designed to be used with a full street harness as well as race harness
Can be used with MC21 and MC28 models or combination of either model (fuel tanks, harnesses and carburetors)
Allows for use of carburetor solenoids and supplied with special mounting hardware
Allows for use of two stroke oil pump and supplied with holes for cables and lines as well as blanking plugs
Uses HRC seal gap , part number 64234-NX5-770 for a good seal with the fuel tank
Built in high grade epoxy and carbon/kevlar for beauty and light weight
Provided with a hole and seal for external fuel cock as well as a short type for racers who want ease of removal of fuel tank.
See also similar product in GRP: BPFX-0007
TYGA no: BPCX-0008
SKU: hon-11311 Categories: ALL products, High performance, RS250R NF5 / NX5, Various partsSeat cowling GRP, Honda NSR250 MC28
€348.13
Seat Cowling, (GRP), MC28 GP-T
We now make four versions of our NSR250 GP Race seat cowling for use for the MC28 in 8 different race and street sets. This product includes ONLY the seat cowling for replacement in the event of an accident or can be used for a project bike of another model. For the MC28, we recommend ordering one of the complete kits below (BPFS-****) which includes all the necessay parts to complete the modification. For installation of any other model the customer will need to make the necessary modifications,
BPFS-0133 (GRP,Street)
BPFS-0134 (GRP Race)
BPFS-0135 (Carbon,Street)
BPFS-0136 (Carbon, Race)
The advantages of this seat cowling over stock include:
– use with rest of seat cowlign kit, much lighter than stock
– new design allows for integrated LED Tail light ( BPLT-0008) for flush fitment and new lighter registration/license plate holder ( BPFX-9006). For race use, location for LED Tail light acts as air vent
– higher at the rear, to give the bike a more agressive stance
– better rider control by use of enclosed seat area
– improved strength with precision in design and fitment
Tyga Performance Compatible Parts for this Product:
This product is compatible with:
BPFX-9033, BPFX-9333, BPCX-9033 and BPCX-9333 Undertray, NSR250 GP-T
TYLY-0108 Subframe, NSR250 GP-T
BPFX-9233 Seat Support, NSR250 GP-T
BPSP-0006 Seat Pad, GP-T
BPAC-0001 Rear Brake Reservoir Kit,
BPLT-0009 LED Taillight
BPFX-9133 Registration Plate Holder GP-T
TYGA no: BPFT-9133
SKU: hon-10465 Categories: ALL products, Bodykit replacement parts, Bodywork and carbon, NSR250 MC28, ShopCarbon tankcover rear, 696/795/796/1100
€104.35
Tank Cover, Rear, (Carbon), Ducati Monster
Boyesen Dual reeds, Cagiva Mito125
€48.76 €46.52
Boyesen Dual reeds, Cagiva Mito125
Boyesen Power Reeds use a patented dual-stage fiberglass design for more airflow, more air velocity and more overall power.
Boyesen dual-stage power reeds produce a better throttle response right off idle and through the mid-range when compared to the traditional Power Reed setup.
1 engine = 1 set
RC Valve Flap L., NSR150SP
€40.35
RC Valve Flap L., NSR150SP
TYGA no: 14203-KW6-840
SKU: hon-11189 Categories: ALL products, Honda, Honda OEM products, New OEM Honda parts, NSR150SP