Front cowling street RC211V TE3, NC30 NC35
€141.68
This products is a replacement part for bodywork sets BPFS-0019, BPFS-0032 and BPFS-0033
TYGA no: BPFU-9023F
SKU: hon-10096 Categories: ALL products, Bodykit replacement parts, Bodykit replacement parts, Bodywork, Bodywork and carbon, Bodywork and carbon, CBR400RR NC29, Honda, RVF400RR NC35, Shop, VFR400RR NC30Big bore kit 300cc wiseco, NSR250 MC18/MC21/MC28
€2,264.37
This 300cc Big Bore Kit is identical to the TPER-0007 300cc Big Bore Kit, but the standard 300cc pistons are replaced with high performance options.
In this case we have forged Wiseco pistons that are lighter and stronger than stock. They use Wiseco rings, clips and pins.
See below for performance details for TPER-0007.
Bore & Stroke is 59mm x 54.5mm giving a total displacement of 298cc.
Parts included in the NSR300 kit.
Cylinder x 2 (includes head studs, RC valve, pulley & nut and washers)
Rear Head x 1
Front Head x 1
Piston x 2
Ring set x 2
Piston Pin x 2
Piston Clip x 4
S/E Bearing x 2
Head gasket x 2
Cylinder gasket x 2
RC Valve cables x 4
Water hose x 1
Exhaust Manifold x 2 (to fit TYGA pipes)
Other information:
There is no problem about the RC valves hitting the piston due to thin cylinder wall thickness. This is not an issue on our kit as it’s using different
cylinders, not modified NSR250. They are genuine OEM Honda cylinders, made and plated in Japan to their typical high quality.
The RC valves are easier to adjust than ever on the 300 kit, as there’s only one adjuster screw to play with, and each cylinder marked at the correct ‘fully open’ position for simple setting.
Exact Jetting requirements for your area and application cannot be provided due to differing atmospheric conditions around the world. However, following are some base settings to work from:
MC21 Std bottom end, Wire splice, TYGA Pipes, Airbox lid mod with filter.
Temp: 29 C
Press: 1015mb
Hum: 65%
Alt: 30m
MJ – #182/#185
JN – Std./Std.
SJ – #38/#38
AS – 1.5 turns out
PwrJ – Std./Std.
Tip: Cooler temps, higher pressure and/or lower humidity require richer jetting. High altitude requires leaner settings. Starting off with rich settings will in the worse case foul a plug. Too lean a setting may destroy the engine.
This jet set-up is for guidance only. TYGA Performance cannot be held responsible for any engine damage incurred due to incorrect settings.
At present, this kit is available by special order. Each kit takes approx. four weeks to prepare.
TYGA no: TPER-3007Â
SKU: hon-10390 Categories: ALL products, High performance, High performance, High performance, High performance, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, ShopCarbon chain guard, Honda CBR600 2003-16
€138.72
This chain guard is made from high quality carbon and replaces the cheap looking stock plastic item. Fits all 600RR models.
Let your bike stand out from the crowd with this beautiful carbon fibre product.
Please note TYGA logos are applied over the clearcoat and can easily be removed.
TYGA no: BPCX-7206
SKU: hon-10002 Categories: ALL products, Carbon, CBR600RR 2003- 4, CBR600RR 2005- 6, CBR600RR 2007- 16, Honda, ShopExhaustset stainless steel aluminium silencer w carbon cap, Honda CBR300
€494.68
The TYGA Full Race System has been designed with maximum power mind. This system is a necessity if you need to squeeze every drop of horse power from the machine.
Manufactured from TIG welded stainless steel sections throughout, with all joints secured by springs, for that ‘factory’ look and feel. For unsurpassed looks, sound and performance, this system is supplied with silencer EXSL-0040. If you need further reason to purchase this product, this exhaust is considerably lighter than the stock system. Weighing only 3 kg instead of the 8 kg of the stock system
This system may not comply to specific country noise emission regulations and is not homologated for street use. Actually it is extremely loud so be warned!
TYGA no: EXPS-0056
SKU: hon-10371 Categories: 4 stroke exhaust sets, ALL products, CBR300R 2014-, Exhausts, Honda, ShopPassenger seat cover (grp), Honda VFR400 NC30
€87.47
This passenger seat cover replaces the passenger seat pad on the NC30. Simply remove the original seat pad and replace with this cover for the RC30 effect! Access to the luggage compartment is still retained.
For use with BPFT-0021 and stock original plastic Honda seat cowling.
TYGA no: BPFX-0021
SKU: hon-10478 Categories: ALL products, Bodywork, Bodywork and carbon, Bodywork and carbon, Honda, Shop, Various parts, VFR400RR NC30Carb Service Kit A, 28 pieces, Suzuki GSXR750-M
€55.41
Carb Service Kit A, 28 pieces, Suzuki GSXR750-M
LiteTek Carburettor Seal Kit to suit: Suzuki GSXR750-M (1991)
Made from long lasting, ethanol resistant elastomers and Viton®
Consist of the following items:
4x FB-008 Float Bowl Ring, Material: Flourosilicone (OE part number: 123258-44B00)
4x OR-005 Pilot Screw O-Ring, Material: Viton 70A (OE part number: 13295-29900)
4x WS-001 Pilot Screw Washer, Material: Stainless Steel (OE part number: 13291-29900)
4x OR-026 Top Cap O-Ring, Material Viton 65 (OE part number: 13278-02340)
4x OR-010 Float Mount O-Ring, Material: Viton 70A (OE part number: 13374-44030 superseeded by 13374-35C00)
4x OR-031 Float Assy O-Ring O-Ring (OE part number: 13374-46710)
4x OR-018 Side Housing O-Ring, Material: Viton70 A (OE part number: 13278-47090)
TYGA no: CKA-Suzuki-GSXR750-M
SKU: alg-10343 Categories: ALL products, Carburettor Service Kits,, SuzukiSeat pad large , flat
€46.69
Vinyl covered medium density foam race seat pad provides a maximum amount of feedback from the bike and minimum comfort!
Underside of seat has velcro stitched in. Kit is supplied with a strip of Velcro with strong 3M adhesive tape appied on the underside. Easy installment. Cut the strip to size using scissors, one each side recommended. Then simply peel back the protective layer on the adhesive strip, lay the strips on the seat cowling and place the seat pad in position.
Compatible Parts:
Tyga Tail cowling: BPFT-9030 BPFS-0102 and BPFS-0103
Belly pan (GRP) Yellow, Honda MSX125 GROM
€225.09 €158.00
Belly Pan, (GRP), MSX125, painted Y-217 Queen Bee Yellow to match your bike. Bling up your grom with this cool component.
Enclosed bottom makes this product suitable for race regulations requiring fluid retention capability.
High quality mounting hardware provided and easy to install.
We also offer the same product with carbon, see BPCL-7228 shown on the bike in the photos.
Note: this product is painted to match Y-217 Queen Bee Yellow. Note we also have a similar product BPFL-7128 YM, (Y-216 Marigold Yellow) which matches the colour of the MSX125 Grom sold in some markets. Be sure to confirm the colour of your bike before ordering.
Note, please check compatibility of under cowl/belly pan with exhaust before ordering. Our products are designed to fit the widest range of products and models but in some cases TYGA products made for the first generation MSX125 Grom are not compatible with the second generation. Please refer to table before ordering.
<p><a href=”{{media url=”wysiwyg/01-belly-pan-fitting-bpfl-bpcl-7128-online-hl-d42c3f6e.pdf”}}” target=”_self”>Click here for PDF</a></p>
TYGA no: Â BPFL-7128 Y
SKU: MSX-10190 Categories: ALL products, Bodywork and carbon, Bodywork and carbon, Honda, MSX125 2013 - 2015, MSX125SF 2016 -2020, Shop