TYGA workshop Apron, Black
€40.61
TYGA Workshop Apron, Black.
Protect your your clothes and work in style with this TYGA-Performance Workshop Apron.
Please contact us for your special requirements for custom-made Workshop Aprons or custom embroidery. Minimum order quantities apply
Oil seal (8x16x5) cylinder, RGV250/RS250
€3.30
Exhaustset race Stainless steel Silencer aluminium round , NC30 NC35
€1,059.04
The TYGA Full Race System has been designed with maximum power in mind. This system is a necessity if you need to squeeze every drop of horse power from the machine.
Manufactured from TIG welded stainless steel sections throughout, with all joints secured by springs, for that ‘factory’ look and feel. The system fits both the NC30 and NC35. Most systems are not designed to be used with a side stand on the NC30, but the TYGA system can be used with a side stand on both the NC30 and NC35.
For unsurpassed looks, sound and performance, this system can be used with any of our 400 system exhaust silencers.
If you need further reason to purchase this product, this exhaust is considerably lighter than the stock system. Weighing only half the weight of the stock system makes for a weight saving of4.2 kg.
NC35:
First, an NC35 was tested with the original Honda exhaust system and produced a peak of 53.5hp; about the right number for a stock bike.
Then the pipe was changed for the TYGA full stainless system, and the main jets increased one size from stock front and rear. No other changes were made, and the peak hp increased to 59.9hp, a gain of 6.4hp (Over 8% more power!)
NC30:
On the NC30, the advantage over the stock exhaust system is higher. With just the TYGA pipe and a couple of main jet changes, the power leaps from a stock 52hp up to a healthy 59hp. That’s 7hp, or 13.5% more.
The pipe set can be used with any silencer with a2 inchinternal diameter bore which is held in place by springs for ease of fitment and removal. TYGA provide the following compatible silencers which can either be ordered separately with this system or together as a set.
The pipe set is supplied with a round aluminium silencer EXSL-0047 which is held in place by springs for ease of fitment and removal. This system may not comply to specific country noise emission regulations and is not homologated for street use.
TYGA no: EXPS-0053
SKU: hon-10358 Categories: 4 stroke exhaust sets, ALL products, By model, By product, Exhausts, Exhausts, Exhausts, Honda, RVF400RR NC35, Shop, VFR400RR NC30Koppelingdeksel Takegawa voor Honda MSX125
€442.17 €373.83
Koppelingdeksel Takegawa voor Honda MSX125
High performance with high quality and durability.
Specially designed to have quick access to the clutch.
Also room for a thermostat and in/outlet for a oil cooler.
TYGA no: 02-01-0150
SKU: msx-10376 Categories: ALL products, High performance, High performance, Honda, MSX125 2013 - 2015, MSX125 GROM, MSX125SF 2016 -2020Exhaust set stainless steel, Aprilia RS125
€355.59
.Set, Exhaust Chamber, Stainless Steel, Aprilia RS-125
Cone welded stainless steel exhaust, for your RS125 performance and look!
The TYGA Performance Aprilia RS-125 Stainless Steel chamber, when used with a TYGA silencer, offers huge saving in weight and increase in power over the stock system. The handcrafted cones are TIG welded together to show the weld rings to maximum affect; this system is a must for the Aprilia RS-125 owner and fits all versions up to and including 2011
This products is the chamber set only and to complete the full replacement exhaust system for your Aprilia RS125 you will need to order a silencer too.
Included in this product:
A.)1 X chamber set (EXCS-0013 or EXCS-0019). When you order this product, you will receive included in the chamber set:
1 X chamber
1 X manifolds with flange and ‘o’ring
2 X manifold to chamber springs
1 X clamp and mounting hardware
Not included in this product is the silencer. Please order separately:
B.)1 X silencer (EXSL-0003, EXSL-0004 OR EXSL-0005) of your choice. Each silencer is provided with mounting hardware and will have a badge attached on the correct side for this system when ordered at the same time.
As is the case with any power upgrade, it is important that you make adjustments to the carburation as necessary. The dyno graph shown had the jetting adjusted one size leaner on the main jet and one clip richer on the needle for optimum performance. However, you will need to adjust your bike’s settings according to your ambient condition. If in doubt, start with a rich setting across the range, and lean off as required. Failure to correctly set up the carburation could result in engine damage.
TYGA no: EXCS-0019Â
SKU: apr-10002 Categories: 2 stroke exhaust sets, ALL products, Aprilia, Exhausts, Exhausts, RS125, ShopSeal, Crank L., MC28
€9.77
Seal, Crank L., MC28
TYGA no: 91205-KV3-771
SKU: hon-11111 Categories: ALL products, High performance, Honda, New OEM Honda parts, NSR250, NSR250 MC21, NSR250 MC28Temperature Sensor, MC21
€62.70
Temperature Sensor, MC21
TYGA no: 37750-PC1-004
SKU: hon-11079 Categories: ALL products, Honda, Honda OEM products, New OEM Honda parts, NSR250, NSR250 MC21Belly Pan Carbon, Yamaha RD250/350 (4LO)
€276.10
Belly Pan, (Carbon) RD250/350LC (4LO)
This belly pan faithfully compliments the classic lines of the legendary ‘Elsie’ along similar lines to the ones used back in the day, complete with the obligatory air scoops on either side. Although the design is traditional, the construction is modern and we have taken advantage of modern materials and techniques to bring you a better product than others on the market.
The belly pan itself is made from 200 gram plain weave carbon coated in three layers of UV resistant PU clearcoat, making it attractive and ready to install. The mounting brackets are laser cut for precision and better aesthetics and they are covered by a plastic coating to give them a firm but kind grip on the frame rails. There is a great deal of adjustability built into the design and to allow our customers to mount this part in exactly the position they desire, based on other modifications such as exhausts, we supply it undrilled.
This product is suitable for stock and our exhaust system, EXCS-0044 which we offer for the RD350LC (4L0)
As well as this carbon fiber version, we also supply a GRP (glass reinforced plastic) version, BPFL-7032