Carbon rear hugger large , Honda CBR1000 2008 – 11
€156.29
This lightweight and attractive rear hugger replaces the stock one and gives much better weather protection and keeps road dirt away from the rear suspension.
Beautiful, perfect fitment and give your bike that HRC look.
2T blank plug, NSR250
€7.37
Replaces the 2T oil injector pump for pre mix use. Secure with liquid gasket such as Three Bond 1104. Must be used with TYLY-0015 Plug holder
Note for blocking the extra 2T feed on later model oil pumps.
On later engines (some MC21 and all MC28, there is an extra oil feed to the cases which can be observed when the oil pump is removed. HRC used to supply a little aluminium plug that you knocked into this extra hole to blank it off. However, that is discontinued so what to do depends on whether the conversion to pre-mix is permanent or not.
If permanant, then we recommend you make sure it’s all clean and degreased, and then fill the hole with epoxy steel. Allow it to cure and it’ll never leak.
If you’re not sure if you’ll ever go back to the oil pump, but would like the option, then we suggest covering the hole with a small thin disc of steel or plastic, and then using a RTV sealant to sort of glue that in place and also block it off. The RTV will stop any leaks, and the small disc will stop any RTV going down the hole. This is then soft enough to be cut away at a later date should you need to.
Compatible products:
TYLY-0015 Plug holder
TYGA no: TYLY-0012
SKU: hon-10388 Categories: ALL products, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, Shop, Various parts, Various parts, Various partsExhaust set slip on, Motogp style stainless steel maggot , Honda MSX125 GROM
€307.40
Set, Pipe, Slip On, MSX125 Grom, Moto Maggot Silencer
Made in stainless steel with spring mounted aluminium silencer, this system significantly increases performance, saves weight and gives the best bang for the buck! (May not comply with noise regulations for some states and territories)
This system is supplied with a Moto Maggot EXSL-8013
Compatibility:
Note, please check compatibility of under cowl/belly pan with exhaust before ordering. Our products are designed to fit the widest range of products and models but in some cases TYGA products made for the first generation MSX125 Grom are not compatible with the second generation. Please refer to table before ordering.
TYGA no: EXPS-0034
SKU: MSX-10004 Categories: ALL products, Exhausts, Exhausts, MSX125 2013 - 2015, MSX125 GROM, MSX125SF 2016 -2020, ShopTriple Clamp Set, CNC, 3D, Silver, NC35 Forks to fit NSR250 MC18
€673.59
CNC machined TYGA triple clamp set for your NSR250 MC28.
These stylish, all aluminium triple clamps are a direct replacement for the MC28 triple clamps, and with the help of FEA testing not only do they look fanstastic, but they perform!
They are delivered ready to fit with all necessary bearings and bottom seal, and even an aluminium top clamp nut, to complete the transformation. The top clamp has the ‘bolt-on’ key holder fitted, which can be removed for racing.
The Steering stoppers are reversible, giving maximum steering lock for street application, or a reduced angle for racing.
Designed and CNC machined in house by TYGA from aircraft spec 6061-T6 alloy.
Tightening recommendations:
Lower clamp pinch bolts: 23Nm.
Top clamp pinch bolts: 23Nm.
TYGA no: TYLY-3301
SKU: hon-11261 Categories: ALL products, CNC parts, CNC parts, Honda, NSR250, NSR250 MC18, Stock list, all modelsSet exhaust without header, race system without silencers
€409.54
This race system has been specifically developed for the KTM RC390 to maximise performance and looks. The dual underseat system eliminates any issues with ground clearance unlike some other systems on the market. In addition, in the event of an accident the exhaust is well protected. Other systems which have the exhaust exiting the right side of the swing arm will usually suffer terminal damage.
Compatiblity: This exhaust can be installed on a bike fitted with the cup race bodywork or standard, with passenger pegs installed or removed. It can be installed with stock registration/turn signal holder.
** Attention ** if you have the EURO 4 type RC390 2016, this means with the exhaust on the right side, not the exhaust under the engine. This exhaust won’t fit, because the header is different. You need to order the full system. Please see product: ktm-10092 / ktm-10093.
For use with stanadard belly pan, we recommend the installation of the exhaust outlet cover BPFC-7431, and for use without passenger pegs, option carbon exhaust guards are available BPCC-0021L and BPCC-0021R.
Please also see EXPS-0061, EXPS-0062, EXPS-0091 and EXPS-0092 for systems complete with silencers.
TYGA no: EXPS-0093
SKU: ktm-10094 Categories: 4 stroke exhaust sets, ALL products, Exhausts, Exhausts, KTM, RC 390, ShopTop triple clamp CNC black , Honda RVF400 -> CBR600 fork
€263.52
Top Triple Clamp, CNC silver, CBR600RR forks NC35/MC21/MC28 Conversion
CNC designed and manufactured in house as a direct replacement for the standard top triple clamp. Facilitates mounting holes for securing the ignition switch holder assy TYLY-0041 for use on NSR conversion or TYLY-0042 for NC35 conversion.
Crafted from aircraft spec 6061-T6 aluminium, using high technology 3D machining, the TYGA clamp offer high strength while being lighter than the standard component, and offers an improved and individual look to your bike.
TYGA bike dust cover Black, Kawasaki Z900RS naked bike size
€90.08
Specially made for your Aprilia.
This cover is handmade from 100% breathable polyester and ideal for an indoor dust cover. Suitable for sports bikes from 125cc to modern 1000cc. sportsbike, the cover features a pull-string around the bottom to secure it in position, comes with its own storage pouch and is machine washable.
Note, this is for indoor use only. For a weatherproof cover, see 08P34-KPP-700 Honda Bike Cover.
TYGA no: TMER-0182
SKU: kaw-10249 Categories: ALL products, Bike covers, Kawasaki, Merchandise, Shop, Universal partsTyre warmers (set) superbike
€339.40 €305.74
All new TYGA Tyre warmers are specifically designed to meet the needs of every racer and track day rider.
Fully adjustable, digital temperature control allows you to set your tyre temperatures to suit every situation with just a press of a button. The remote control box allows for quick and easy monitoring of temperatures.
Tyre warmers are an essential tool for any track excursion. For the racer it allows for lightening first lap action to get the jump on your competitor, and for the track day specialist there’s no more wasted laps trying to get heat into your tyres.
Another great feature is that you can refit the warmers between session and just set at a lower temperature to stop your tyres heat cycling . This gives you more tyre grip for longer, so your tyre won’t go off half way through the day.
These wamers are designed for Superbikes running the usual 120 front tyre, and 190-200 section rear tyre.
TYGA tyre warmers are designed to run on 220V, and use a C type plug. Power rating is 550W rear and 450W front.
TYGA no: TWDS-0007
SKU: alg-10145 Categories: ALL products, CBR1000 2004-7, CBR1000 2008-11, CBR1000 2012-, CBR900RR 1992- 95, GSX-R1000 K5-K6, GSX-R1000 K7-K8, GSX-R1000 K9-K10, Honda, Kawasaki, Shop, Suzuki, Tyre warmers, VFR750R RC30, Yamaha, YZF-1000 R1 2002- 6, YZF-1000 R1 2007- 8, YZF-1000 R1 2009- 14, ZX10R 2011 -15