Harness, Lambda, Ninja 250/300 2013-
€17.42
Harness, Lambda, Ninja 250/300 2013-
This is an extension to allow the lambda sensor to be plugged into the stock wiring harness from its position on the right of the bike. (The stock exhaust runs up the left side and the harness is too short without this extension)
Seal, Crank Right, MC28
€39.58
Seal, Crank Right, MC28
TYGA no: 91203-KV3-681
SKU: hon-11113 Categories: ALL products, High performance, Honda, New OEM Honda parts, NSR250, NSR250 MC28Fairing set race RSW, Honda NSR250 MC21/MC28
€492.13
This set of bodywork is designed for race use and comprises the parts below which are also available separately.
* A clear screen is provided unless you specify tinted in the comment box at check out,
Laminated in top quality molds by our skilled and experienced workers, TYGA Performance fiberglass products are renowned for their quality and value for money. Order with confidence.
Take a look at our Project bikes page, to see the actual product on a bike or just to get some ideas.
TYGA no: BPFS-0002Â
SKU: hon-10220 Categories: ALL products, Bodywork, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Honda, NSR250 MC21, NSR250 MC28, ShopAirbox "GRP", Honda NSR250 MC21/MC28
€423.04
Airbox, GRP, NSR250 MC21/MC28
This high quality GRP air box is an adaptation of the HRC air box and has the following features.
Maximum volume, more than double the size of the stock air box for better flow and power
High flow, large area foam filter for street use
Snug fitting rubber base to prevent leaks around carb insulators
Designed to be used with a full street harness as well as race harness
Can be used with MC21 and MC28 models or combination of either model (fuel tanks, harnesses and carburetors)
Allows for use of carburetor solenoids and supplied with special mounting hardware
Allows for use of two stroke oil pump and supplied with holes for cables and lines as well as blanking plugs
Uses HRC seal gap , part number 64234-NX5-770 for a good seal with the fuel tank
Built in high grade epoxy and GRP for light weight
Provided with a hole and seal for external fuel cock as well as a short type for racers who want ease of removal of fuel tank
See also BPCX-0007 for the same airbox in carbon/kevlar
*please do note some product photos are for reference and show the Carbon/Kevlar version fitted on our NSR250 project bike
TYGA no: BPFX-0007
SKU: hon-11070 Categories: ALL products, Bodywork and carbon, High performance, High performance, High performance, Honda, NSR250, NSR250 MC21, NSR250 MC28Carb Service Kit A, 39 pieces, Honda CBR400RR NC23
€72.27
Carb Service Kit A, 39 pieces, Honda CBR400RR NC23
LiteTek Carburettor Seal Kit to suit
Honda CBR400RR NC23(G-H-J-K)
Made from long lasting, ethanol resistant elastomers and Viton®
Consist of the following items:
4x FB-006 Float Bowl Ring, Material: Flourosilicone (Part of Honda Assembly Part No. 16010-MN4-003 superseded by 16010-MN4-305)
4x OR-005 Pilot Screw O-Ring, Material: Viton 70A (Part of Honda Assembly Part No. 16010-MN4-003 superseded by 16010-MN4-305)
4x WS-001 Pilot Screw Washer, Material: Stainless Steel
4x OR-009 Drain Screw O-Ring, Material: Viton 70A (Part of Honda Assembly Part No. 16010-MN4-003 superseded by 16010-MN4-305)
6x OR-018 Vacuum Breather O-Ring, Material Viton 70A (The parts book lists the part number for the vacuum o-rings as being part of the kit 16040-MM5-601. However, that kit only contains the o-rings for the fuel tubes and float bowl breather tee pieces. Therefore, we have added these o-rings to the kit)
4x OR-011 Float Breather O Ring, Material: Viton 70A (Part of Honda Assembly Part No. 16040-MN4-003 superseded by 16040-MM5-601)
6x OR-016 Fuel O-Ring, Material: Viton 70A (Part of Honda Assembly Part No. 16040-MN4-003 superseded by 16040-MM5-60)
4x CS004 Choke Plunger Cap, Material: HNBR (Part of Honda Assembly Part No. 16046-KT8-003 or 16046-KY2-711)
3x SC-008 Throttle Synch Screws, Material: Stainless Steel
TYGA no: CKA-Honda-NC23
SKU: alg-10357 Categories: ALL products, Carburettor Service Kits,, CBR400RR NC23, HondaCarbon Headlight cover, Honda MSX125 GROM
€191.80
Carbon headlight cowling, let your bike stand out from the crowd
TYGA no: BPCU-7028
SKU: MSX-10116 Categories: ALL products, Bodywork and carbon, MSX125 2013 - 2015, MSX125 GROM, ShopFront cowling street RC211V TE3, NC30 NC35
€141.68
This products is a replacement part for bodywork sets BPFS-0019, BPFS-0032 and BPFS-0033
TYGA no: BPFU-9023F
SKU: hon-10096 Categories: ALL products, Bodykit replacement parts, Bodykit replacement parts, Bodywork, Bodywork and carbon, Bodywork and carbon, CBR400RR NC29, Honda, RVF400RR NC35, Shop, VFR400RR NC30TYGA bike dust cover Black HRC street
€81.90
TYGA Bike Dust Cover, Black, HRC (street)
This cover is handmade from 100% breathable polyester and ideal for an indoor dust cover. Suitable for sports bikes from 125cc to modern 1000cc. sportsbike, the cover features a pull-string around the bottom to secure it in position, comes with its own storage pouch and is machine washable.
See also TMER-0124 for the “Race” version of this TYGA bike dust cover for (race) bikes with no mirrors
Note, this is for indoor use only. For a weatherproof cover, see 08P34-KPP-700 Honda Bike Cover.
TYGA no: TMER-0123
SKU: hon-11073 Categories: ALL products, Bike covers, CBR1000 2004-7, CBR1000 2008-11, CBR1000 2012-, CBR125R/CBR150R 2004-10, CBR125R/CBR150R 2011-, CBR250R 2011 - 15, CBR250R MC19, CBR250RR MC22, CBR300R 2014-, CBR400RR NC23, CBR400RR NC29, CBR500R, CBR600RR 2003- 4, CBR600RR 2005- 6, CBR600RR 2007- 16, CBR900RR 1992- 95, Hawk/Bros 400/650, Honda, Merchandise, NR750, NSR125 JC22 1994 - 2003, NSR150SP, NSR250, NSR250 MC18, NSR250 MC21, NSR250 MC28, NSR500V, RC36-2 -> RC30 replica products, RS250R NF5 / NX5, RVF400RR NC35, RVF750 RC45, Shop, Universal parts, Various parts, Various parts, Various parts, Various parts, various parts, Various parts, Various parts, Various parts, Various parts, Various parts, VFR400RR NC30, VFR750F Gen 3 90-93, VFR750F Gen 4, 94-97, VFR750R RC30, VTR1000Sp1SP2