Oops this is 404! Let's help you find what you were looking for...

Tyga Europe Performance Parts provides a wide range of motorparts for your bike! 

Carbon Rear hugger with chainguard, Suzuki RGV 250 VJ23

216.82

(262.35 inc. VAT )

Rear Hugger/Chain Guard (Carbon), VJ23 RGV250

The VJ23 RGV250 is the only RGV250 model which does not have a rear hugger as standard and as a result, all the road filth and rain tends to collect around the rear shock and under side of the seat cowling. TYGA Performance have developed this carbon hugger as a solution to the dirt issue while making the swing arm/rear wheel part of the bike more attractive. Designed to fit onto the contour of the VJ23 swing arm’s fabrication and lock into position by a rub underneath, the TYGA hugger incorporates the rear chain guard too, using the chain guard’s mounting holes on the left to hold it securely in place. On the right side, it is held on by a cable tie through the rear brake line guide and at the front by an M4 bolt which is requires drilling and tapping of the swing arm by the customer to install this product.

IMPORTANT, note that due to the VJ23 never having the option for a rear hugger, there is no position provided on the swing arm to mount the hugger at the front and it is necessary to drill and tap an M4 hole in the swing arm and use a cable tie to provide a good level of support for the hugger. See photos 7 and 8 for details on what is required to install this product.

Complete with all fitting hardware.

TYGA no: BPCH-9003

SKU: suz-10187 Categories: , , ,
Read more

Wheel, Front, Aluminium Spacer Kit, Ninja 400

17.53

(21.21 inc. VAT )

Wheel, Front, Aluminium Spacer Kit, Ninja 400

Replace the heavy steel rear wheel spacers with these “self-retaining” lightweight 6061-T6 aluminium spacers.

The outer spacers are designed with a lip that slips in behind the seal to retain the spacers in the wheel. No more lost spacers rolling across the workshop floor!

Lighter weight allows the suspension to react more positively, so better handling and good looks!

TYGA no: TPER-0059

SKU: kaw-10095 Categories: , , , , ,
Read more

Seal Thermostat Housing, MC18~28

11.04

(13.36 inc. VAT )

Seal Thermostat Housing, MC18~28

Read more

Aluminium meterstay, Honda RVF400 NC35

216.94

(262.50 inc. VAT )

Direct replacement of the stock item. Fabricated from aluminium alloy, this Tyga Lyte product weighs approx. 200g. and can be used with all other NC35 components and fairings except the Tyga RC211V style uppers, BPFU-0018 and BPFU-0020.

TYGA no: TYLY-0017

SKU: hon-10154 Categories: , , , , ,
Read more

TYGA / Kitaco Power up kit carbon , Honda MSX125 GROM

675.60

(817.48 inc. VAT )

TYGA/KITACO Power Up Kit, Carbon Type

This power up kit is designed to give a significant power boost over stock. Using TYGA Performance and KITACO products, the power of the MSX125 Grom is increased by 25%. Below is the dyno graph. STD vs our full system with carbon silencer, Kitaco type 2 camshaft, i-map (setting #3). Similar results were found with the Moto Maggot and stainess type silencers.

Parts

This product consists of the components shown below, namely:

EXPS-0041 Set, Pipe, Full Race System, MSX125 Grom, Carbon Oval/Carbon End Cap

KIT-300-1432010 KITACO Type 2 Camshaft

KIT-763-1432010 KITACO i-Map. Fuel Injection Controller

For those who want a Type 1 camshaft, please put this in the commentbox at check out.

Option:

KIT-763-0500900 i-Map interface cable. To adjust the i-map for special setting. Software available on KITACO website.

Description:

Fitting this Power Up Kit to your Honda MSX125/GROM gives a significant increase in top end performance and over rev. Peak hp is moved from 7,000rpm (std) up to 8,000rpm, with a 1.6hp gain at peak.

Fitting the i-Map Fuel Injection Controller is a necessary modification to avoid the engine running lean and being damaged. Running the KITACO Type 2 camshaft without the i-Map is NOT an option!

The wire harness requires modification and the documents are included with the kit, or can be viewed here: http://www.kitaco.co.jp/data/product/link/instaling_manual/kitaco_installing_manual_grom_imap.html

The i-Map is shipped with “setting #3” activated. This is the basic map for this kit, but the map can be modified using the optional i-Map interface cable and software downloadable from the KITACO website:

i-Map Fuel Manager: http://www.kitaco.co.jp/dlservice.html

Read more

Exhauststay left TYGA VJ21, Suzuki RGV250 VJ21

52.50

(63.53 inc. VAT )

This product is designed to be installed as part of our TYGA Seat cowling kit for the VJ21 Kit BPFS-0121 and substitutes for the stock passenger peg hangers. It retains the use of stock mounting hardware and there is a level of adjustability in the mounting position due to the slot for the clamp position.

This product can be used as a stand alone item and does not need the rest of the kit and is suitable for replacing passenger pegs on any race VJ21 for example.

Please note this product is ‘handed’ and you need one of each TYLY-0100L and TYLY-0100R for one bike.

TYGA no: TYLY-0100L

SKU: suz-10100 Categories: , , , , ,
Read more

Upper fairing set street RC211V, CBR250RR MC22

451.91

(546.81 inc. VAT )

This set of bodywork comprises of the parts shown below which are also available separately

*A clear screen is provided unless you specify tinted in the comment box at check out

This kit is supplied with all additional fasteners required to mount it to a stock MC22. It fits to the original meter and mirror stays and uses the Honda mounting points and fasteners for mirrors. Where it mounts to the lower cowling and frame, it uses the original Honda bolts and clips (not supplied)

TYGA no: BPFS-0015

SKU: hon-10202 Categories: , , , ,
Read more