lower cowling (GRP), stock shape NSR250 MC21/MC28
€241.47
Lower Cowling (GRP), NSR250, MC21/28, Stock Shape, Assy
This part is a direct replacement for the OEM Honda left, right lower, right mid and inner cowls and has the ‘shark fin’ and front ducts retained. Compatible with stock and Tyga exhaust systems.
Compatible Parts:
Can be used with the following upper cowlings: MC21 and MC28 OEM upper cowling, Tyga upper cowlings: BPFU-0001, BPFU-0002, BPFU-0003, BPFU-0006, BPFU-0007, BPFU-0008 and BPFU-0022
See also
BPFL-0001 for similar product
TYGA no: BPFL-9001
SKU: hon-10915 Categories: ALL products, Bodykit replacement parts, Bodykit replacement parts, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, High performance, Honda, NSR250, NSR250 MC21, NSR250 MC28Kit, Fairing Set, Street, GRP, Stock Shape, VJ21
€662.38
Kit, Fairing Set, Street, GRP, Stock Shape, VJ21
Complete set of stock shaped bodywork for the Suzuki RGV250 VJ21
Consists of the following products ( also available seperatly)
BPFU-0019 Upper Fairing
BPFL-0019 Lower Fairing
BPFT-0019 Seat Cowling
BPFF-0019 Front Fender
SCRE-0120 Clear Screen
TYGA no: BPFS-0190
SKU: suz-10121 Categories: ALL products, Bodywork, Bodywork and carbon, RGV250 VJ21, Suzuki, Suzuki RGV2502T blank plug, NSR250
€7.37
Replaces the 2T oil injector pump for pre mix use. Secure with liquid gasket such as Three Bond 1104. Must be used with TYLY-0015 Plug holder
Note for blocking the extra 2T feed on later model oil pumps.
On later engines (some MC21 and all MC28, there is an extra oil feed to the cases which can be observed when the oil pump is removed. HRC used to supply a little aluminium plug that you knocked into this extra hole to blank it off. However, that is discontinued so what to do depends on whether the conversion to pre-mix is permanent or not.
If permanant, then we recommend you make sure it’s all clean and degreased, and then fill the hole with epoxy steel. Allow it to cure and it’ll never leak.
If you’re not sure if you’ll ever go back to the oil pump, but would like the option, then we suggest covering the hole with a small thin disc of steel or plastic, and then using a RTV sealant to sort of glue that in place and also block it off. The RTV will stop any leaks, and the small disc will stop any RTV going down the hole. This is then soft enough to be cut away at a later date should you need to.
Compatible products:
TYLY-0015 Plug holder
TYGA no: TYLY-0012
SKU: hon-10388 Categories: ALL products, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, Shop, Various parts, Various parts, Various partsCarb Service Kit B, 23 pieces, Honda CBR250R MC14, MC17 & MC19
€43.36
Carb Service Kit B, 23 pieces, Honda CBR250R MC14, MC17 & MC19
LiteTek Carburettor Seal Kit to suit
Honda CBR250R MC14, MC17 & MC19
Made from long lasting, ethanol resistant elastomers and Viton®
Consist of the following items:
4x OR-011 Float Breather O-Ring, Material: Viton 70A, (Part of Honda Assembly Part No. 16040-KT7-003)
6x OR-016 Fuel T-Pipe O-Ring, Material: Viton 70A, (Part of Honda Assembly Part No. 16040-KT7-003)
6x WS-018 Vacuum Breather O-Ring, Material: Viton 70A, (Part of Honda Assembly Part No. 16040-KT7-003)
4x CS-004 Choke Plunger Cap, Material: HNBR, (Part of Honda Assembly Part No. 16046-KT7-003 or 16046-KT8-003)
3x SC-008 Throttle Synch Screws, Material: Stainless Steel
TYGA no: CKB-Honda-MC19
SKU: alg-10362 Categories: ALL products, Carburettor Service Kits,, CBR250R MC19, HondaO- ring for TYGA silencer 2 stroke
€4.33
O- ring for TYGA silencer 2 stroke
TYGA no: EXOR-000
SKU: alg-10116 Categories: 2 stroke exhaust sets, ALL products, Aprilia, Cagiva, Exhausts, Exhausts, Exhausts, Exhausts, Exhausts, Exhausts, Exhausts, Exhausts, Exhausts, Honda, Mito 125, NSR125 JC22 1994 - 2003, NSR150SP, NSR250 MC18, NSR250 MC21, NSR250 MC28, RGV250 VJ21, RGV250 VJ22, RGV250 VJ23, RS125, RS250, Shop, Suzuki, Yamaha, YZ250 2005-15Meterstay aluminium Race , Honda VFR400 NC30
€202.46
Meter Stay, NC30, Race, Stock Type, Assy
This meter stay to be used with all stock shaped bodywork. It is the same dimensions as Honda part 64501-MR8-000 and TYGA part TYLY-0016 but is designed with track use in mind . Made from aluminium and designed without any headlight mounts, this simple and lightweight stay is suitable for race and track day applications.
Compatible with stock Honda NC30 bodywork and TYGA parts BPFU-1021 and BPFS-0139
TYGA no: TYLY-0250
SKU: hon-11215 Categories: ALL products, Honda, Shop, Various parts, VFR400RR NC30Carbon luggage compartment lid, Honda VRT1000 SP1/SP2
€99.35
This is a direct replacement for the OEM Honda part. To be used with our carbon seat cowling or can be used with the OEM Honda plastic seat cowling
TYGA bike dust cover Red/Black RVF
€63.10
TYGA Bike Dust Cover, Red/Black Honda RVF
This cover is handmade from 100% breathable polyester and ideal for an indoor dust cover. Suitable for sports bikes from 125cc to modern 1000cc. sportsbike, the cover features a pull-string around the bottom to secure it in position, comes with its own storage pouch and is machine washable.
Note, this is for indoor use only. For a weatherproof cover, see 08P34-KPP-700 Honda Bike Cover.
Please contact us for your special requirements for custom-made dust covers or custom screen printing. Minimum order quantities apply.
TYGA no: TMER-0081
SKU: hon-10924 Categories: ALL products, Bike covers, Merchandise, RVF400RR NC35, RVF750 RC45, Shop, Universal parts, Various parts