Big bore kit 300cc wiseco VHM, NSR250 MC18/MC21/MC28
€2,842.71
Big Bore Kit, NSR300, Wiseco, VHM *
This 300cc Big Bore Kit is identical to the TPER-0007 300cc Big Bore Kit, but the standard 300cc heads and pistons are replaced with high performance options.
In this case we have forged Wiseco pistons that are lighter and stronger than stock, and also changable insert VHM cylinder heads, which have been specifically developed by TYGA and VHM for use with the TYGA 300cc Big Bore Kit.
See below for performance details for TPER-0007.
Bore & Stroke is 59mm x 54.5mm giving a total displacement of 298cc.
Parts included in the NSR300 kit.
Cylinder x 2 (includes head studs, RC valve, pulley & nut and washers)
Rear Head x 1
Front Head x 1
Piston x 2
Ring set x 2
Piston Pin x 2
Piston Clip x 4
S/E Bearing x 2
Head gasket x 2
Cylinder gasket x 2
RC Valve cables x 4
Water hose x 1
Exhaust Manifold x 2 (to fit TYGA pipes)
Other information:
There is no problem about the RC valves hitting the piston due to thin cylinder wall thickness. This is not an issue on our kit as it’s using different
cylinders, not modified NSR250. They are genuine OEM Honda cylinders, made and plated in Japan to their typical high quality.
The RC valves are easier to adjust than ever on the 300 kit, as there’s only one adjuster screw to play with, and each cylinder marked at the correct ‘fully open’ position for simple setting.
Exact Jetting requirements for your area and application cannot be provided due to differing atmospheric conditions around the world. However, following are some base settings to work from:
MC21 Std bottom end, Wire splice, TYGA Pipes, Airbox lid mod with filter.
Temp: 29 C
Press: 1015mb
Hum: 65%
Alt: 30m
MJ – #182/#185
JN – Std./Std.
SJ – #38/#38
AS – 1.5 turns out
PwrJ – Std./Std.
Tip: Cooler temps, higher pressure and/or lower humidity require richer jetting. High altitude requires leaner settings. Starting off with rich settings will in the worse case foul a plug. Too lean a setting may destroy the engine.
This jet set-up is for guidance only. TYGA Performance cannot be held responsible for any engine damage incurred due to incorrect settings.
At present, this kit is available by special order. Each kit takes approx. four weeks to prepare.
TYGA no: TPER-1007
SKU: hon-10391 Categories: ALL products, High performance, High performance, High performance, High performance, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, ShopTYGA bike dust cover Red Honda wing silver
€65.05
TYGA Bike Dust Cover, Blue, Rothmans Honda
This cover is handmade from 100% breathable polyester and ideal for an indoor dust cover. Suitable for sports bikes from 125cc to modern 1000cc. sportsbike, the cover features a pull-string around the bottom to secure it in position, comes with its own storage pouch and is machine washable.
Note, this is for indoor use only. For a weatherproof cover, see 08P34-KPP-700 Honda Bike Cover.
TYGA no: TMER-0157
SKU: hon-11301 Categories: ALL products, Bike covers, By model, CBR1000 2004-7, CBR1000 2008-11, CBR1000 2012-, CBR125R/CBR150R 2004-10, CBR125R/CBR150R 2011-, CBR250R 2011 - 15, CBR250R MC19, CBR250RR 2017, CBR250RR MC22, CBR300R 2014-, CBR400RR NC23, CBR400RR NC29, CBR500R, CBR600RR 2003- 4, CBR600RR 2005- 6, CBR600RR 2007- 16, CBR900RR 1992- 95, Honda, Merchandise, NSR150SP, NSR250, NSR250 MC18, NSR250 MC21, NSR250 MC28, NSR500V, NSR500V NX6, RC36-2 -> RC30 replica products, RS250R NF5 / NX5, RVF400RR NC35, RVF750 RC45, Shop, Universal parts, Various parts, Various parts, Various parts, Various parts, various parts, Various parts, VFR400RR NC30, VFR750F Gen 3 90-93, VFR750F Gen 4, 94-97, VFR750R RC30, VTR1000Sp1SP2Carbon air intake RC211V, NC29 NC30
€126.30
This airduct is a direct replacement for the fiberglass version which is supplied with our RC211V style fairings such as BPFU-9118 and BPFU-9017
TYGA no: BPCX-9008
SKU: hon-10073 Categories: ALL products, Bodykit replacement parts, Bodykit replacement parts, Bodywork and carbon, Bodywork and carbon, Carbon, CBR400RR NC29, Honda, RVF400RR NC35, Shop, VFR400RR NC30Carbon cover for exhaust outlet , KTM RC390
€108.71
Cover, Exhaust Outlet, (Carbon), KTM RC390
This cover fills the outlet hole left in the stock belly pan after installation of an under seat or similar exhaust. Easy to install, supplied with mounting hardware and painted white to blend in.
TYGA no: BPCC-7431
SKU: ktm-10070 Categories: ALL products, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Carbon, Exhausts, KTM, RC 390, ShopVHM Cyl. headset Suzuki RM125 ’05-
€271.95 €256.04
VHM Cyl. headset Suzuki RM125 ’05-> (alg-10204) AA33078
VHM are a respected manufacturer of high quality racing parts used by factory teams world wide.We are pleased that we can offer VHM products on our website.VHM produces exchangeable cylinder heads for two-stroke engines in motocross and road racing. With the experience gained in two-stroke tuning, VHM develops products of high quality.During intensive tests, on the racetrack as on the VHM dyno, the cylinder head showed a better temperature development in the cylinder head. A lower engine temperature followed. The explanation of this phenomenon is the use of a special aluminum alloy which has a very good heat transference. Another advantage of the material is its resistance to detonation.The VHM cylinder head is designed with central spark plug position for superior burn, and removable combustion chamber inserts so that changes of compression ratios are quick and simple, and no more wasted head gaskets thanks to the O-ring designThis head set comes with following parts:1x cylinder head1x standard insert (11.20cc)Optional inserts:– blind– 10.80– 11.00– 11.40This VHM head set uses the standard water hose spigots. The standard spark plugs may be used.Note: please put in comment box, the year of your bike and what size insert you want (no comment is STD insert).Detailed instruction on the setting up of VHM heads can be found on their website at www.vhm.nl
TYGA no: AA33078Â Â Â Â Â Â Â Â
SKU: alg-10204 Categories: ALL products, Motocross, Shop, Suzuki, Suzuki MX, VHM productsCarbon heel guard right, VJ22/ NC30/NC35
€37.61
This lightweight carbon heel guard can be used as a direct replacement for the heavy steel one on the VJ22 RGV250. It can also be fitted to many other models, being suitable for most models which have Nissin master cylinders with 45-49 mm. pitch mounting holes.
Note this product is not supplied with STAA-0002 and STAA-0003 step kits but it is supplied with STAA-0004. Please add this product to your cart if you require a right side carbon heel guard for the STAA-0002 and STAA-0003.
TYGA no: BPCC-9002
SKU: alg-10047 Categories: ALL products, Carbon, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, RGV250 VJ21, RGV250 VJ22, RVF400RR NC35, Shop, Suzuki, Various parts, Various parts, Various parts, Various parts, Various parts, Various parts, Various parts, VFR400RR NC30Kit, Fairing Set, Street, GRP, Stock Shape, VJ21
€662.38
Kit, Fairing Set, Street, GRP, Stock Shape, VJ21
Complete set of stock shaped bodywork for the Suzuki RGV250 VJ21
Consists of the following products ( also available seperatly)
BPFU-0019 Upper Fairing
BPFL-0019 Lower Fairing
BPFT-0019 Seat Cowling
BPFF-0019 Front Fender
SCRE-0120 Clear Screen
TYGA no: BPFS-0190
SKU: suz-10121 Categories: ALL products, Bodywork, Bodywork and carbon, RGV250 VJ21, Suzuki, Suzuki RGV250Heel Guard, Carbon, Pair, Honda JC22 NSR125
€151.77
Real Carbon fibre reproduction of the stock OEM Honda front fender. Finished in high gloss, adds beauty and reduces unsprung weight. (weight of part approx. 0.2 kg)
TYGA no: BPCC-7035
SKU: hon-11349 Categories: ALL products, Carbon, Honda, NSR125 JC22 1994 - 2003, Shop