Set full race system under belly with long stainless silencer + carbon side cover, Honda Monkey 125 2018- BP5624
€731.40
Set, Pipe, Full System, Underbelly, Monkey 125, Stainless Oval/Carbon End Cap, Long, with Carbon Side Cover
This full race system has been specifically designed for the Monkey 125 to maximise power. Made in stainless steel with spring mounted stainless silencer this system increases performance, saves weight and enhances the looks of the bike. Sounds great too! (A dB killer is included).
Note that once the stock system has been removed from the Monkey, there is an empty space under the seat on the right side. This set includes Carbon Side Cover BPCC-7142R which has been designed to mirror the left side cover. This will fill in the gap under the seat and complete the transformation. Refer to photos of the exhaust installed for more details.
Performance and Dynograph
The blue trace shows the 100% standard Honda Monkey 125, compared to the red trace, which is after installing the TYGA Full System set (EXPS-0107) with no other changes to the stock bike.
A useful increase in peak power and further gains could probably be had with remapping etc.
Similar Products:
Please also see:
EXPS-0108 Stainless, Underbelly, with short silencer
Top End Rebuild Kit MC18, Cyl. B, Assy.
€293.88
Below is everything you need to do a top end rebuild on your MC18. Suitable for cylinder ‘B’. One kit includes all parts for one cylinder. To overhaul both cylinders please order 2 kits.
There are different kits depending on the piston supplied and the pistons are sized to match the cylinder. The cylinders have a letter stamped on them. A cylinder = B piston B cylinder = no mark piston, C cylinder = D piston. The largest cylinder bore is A and the smallest is C. However, note that this is only for when cylinders are new or in good condition, so if the cylinder is worn, the corresponding piston will be a looser so a bigger piston might be advised. If the cross hatch honing of the cylinder is very feint then we suggest using the next size up piston. The differences in sizes are tiny (11 microns between largest and smallest) and for the most part not an issue so it is not a problem if a smaller piston is used in a larger cylinder or the other way round.
Cylinder A = 54.008mm – 54.011mm use Piston B = 53.966mm – 53.969mm
Cylinder B = 54.004mm – 54.008mm use Piston # = 53.962mm – 53.965mm
Cylinder C = 54.000mm – 54.004mm use Piston D = 53.958mm – 53.961mm
Piston to bore clearance = 0.039mm – 0.045mm
TYGA no: NHPS-0002B
SKU: hon-10837 Categories: ALL products, High performance, High performance, Honda, New OEM Honda parts, NSR250, NSR250 MC18Set exhaust pipe with stainless steel silencer, Yamaha R25/R3
€765.52
Set, Exhaust Pipe, Race System, Yamaha R25/R3, Stainless, Round Aluminium Silencer
This race system has been specifically developed for the Yamaha YZF R25 and YZF R3 and has been designed for optimum performance. It uses a stainless oval silencer with carbon end cap to keep sound to a minimum. As well as the improved performance, it saves weight over the stock system and of course, it looks awesome!
Compatiblity
This exhaust can be installed on a bike fitted with the stock or with race bodywork and with or without the passenger pegs installed.
No modification of bodywork is required, however, the emission canister must be relocated using the clamp provided.
Please also see EXPS-0072 EXPS-0073 and EXPS-0075 for similar system.
Performance and Dynograph
Please refer to dynographs
A) All Standard.
The standard exhaust system is replaced with the TYGA system. No modifications to the engine or fuelling were performed. Fitting a fuel controller could further increase the performance gains.
B) Airfilter/Airbox modification.
The standard exhaust system is replaced with the TYGA system. The airbox cover has been removed and a high flow filter fitted. This improves power all through the range. Fitting a fuel controller could further increase the performance gains.
TYGA no: EXPS-0074
SKU: yam-10061 Categories: 4 stroke exhaust sets, ALL products, Exhausts, Yamaha, YZF-R25/R3Kit, Complete Body Set, Stock Shape, with Seat Cover, NC30, Painted Type 1
€1,643.89
Fuel Tank, Carbon, VFR400R NC30
Top quality reproduction of the steel NC30 fuel tank in carbon fiber. This product is a direct replacement for the stock NC30 fuel tank and saves approx. a third of the weight of the stock one (2.6 kg ours, 3.9kg for the steel one).
Finished in high quality UV resistant clearcoat to show off the beauty of the carbon weave, and using specially formulated epoxy resin for fuel resistance, this tank has been tested with a range of fuels from 95 unleaded pump fuel to E85 (85% ethanol).
Laminated with a Kevlar layer for abrasion and puncture resistance, this fuel tank is both strong and light. Unlike most aftermarket fuel tanks, this one is designed so that there is no compromise with installation and through use of high quality CNC machined aluminium inserts, retains the original associated hardware including the stock Honda or keyless fuel tank filler caps and stock fuel cock.
Like the stock Honda fuel tank, it has the correct plumbing for the Honda type breather valve incorporated in the design and also the overflow/drain tube. Uses the stock Honda mounting rubbers for ease and peace of mind in fitment.
TYGA no: BPFS-0218
SKU: hon-11403 Categories: ALL products, Bodywork and carbon, Carbon, Honda, Shop, VFR400RR NC30Needle roller bearings, set MC16 and MC18 (R2J/R4J)
€51.65
Crankshaft Bearing, Right, NSR250 MC21/28
Genuine OEM KOYO main crankshaft bearing for your Honda NSR250 MC21/28.
See also TYPP-0012SET for set consisting of one each of the left, centre and right crank bearings.
TYGA no: TPER-5008
SKU: hon-11432 Categories: ALL products, High performance, Honda, NSR250, NSR250 MC18Shroud right white, Honda MSX125 GROM
€32.45
Shroud right white, Honda MSX125GROM (msx-10017)
OEM Honda part
TYGA no: 83480-K26-900ZC
SKU: MSX-10018 Categories: ALL products, Honda, MSX125 2013 - 2015, OEM parts, ShopRacing step kit CNC silver, Suzuki RGV 250 VJ21
€371.00
Designed in-house by TYGA Performance using the latest CAD/CAM software, these CNC machine-made step kits are made from top quality aircraft grade aluminium. Complete with carbon heelguards on both left and right hanger.
Exhaust mount rubbers and bushes from standard steps should be fitted to the TYGA steps.
Now includes rear brake light switch provision.
This step kit moves the peg position back 5 mm. and up 20 mm. from standard. Pitch of hanger frame mounting holes is 88 mm.
Perfect for street use, but also very handy on track. Because all parts from this race step are available separately.
Reverse schifting is possible with this race step kit.
TYGA no: STAA-0010
SKU: suz-10060 Categories: ALL products, CNC parts, RGV250 VJ21, Shop, Suzuki, Various partsCarbon airduct (pair), Honda NSR125 JC22
€240.81
Air Ducts, Pair, (Carbon) JC22 NSR125
Real Carbon fibre reproduction of the stock OEM Honda front fender. Finished in high gloss, adds beauty and makes your bike stand out from the crowd.
TYGA no: BPCX-7035
SKU: hon-10481 Categories: ALL products, Carbon, Honda, NSR125 JC22 1994 - 2003, Shop