Big bore kit 300cc wiseco, NSR250 MC18/MC21/MC28
€2,264.37
This 300cc Big Bore Kit is identical to the TPER-0007 300cc Big Bore Kit, but the standard 300cc pistons are replaced with high performance options.
In this case we have forged Wiseco pistons that are lighter and stronger than stock. They use Wiseco rings, clips and pins.
See below for performance details for TPER-0007.
Bore & Stroke is 59mm x 54.5mm giving a total displacement of 298cc.
Parts included in the NSR300 kit.
Cylinder x 2 (includes head studs, RC valve, pulley & nut and washers)
Rear Head x 1
Front Head x 1
Piston x 2
Ring set x 2
Piston Pin x 2
Piston Clip x 4
S/E Bearing x 2
Head gasket x 2
Cylinder gasket x 2
RC Valve cables x 4
Water hose x 1
Exhaust Manifold x 2 (to fit TYGA pipes)
Other information:
There is no problem about the RC valves hitting the piston due to thin cylinder wall thickness. This is not an issue on our kit as it’s using different
cylinders, not modified NSR250. They are genuine OEM Honda cylinders, made and plated in Japan to their typical high quality.
The RC valves are easier to adjust than ever on the 300 kit, as there’s only one adjuster screw to play with, and each cylinder marked at the correct ‘fully open’ position for simple setting.
Exact Jetting requirements for your area and application cannot be provided due to differing atmospheric conditions around the world. However, following are some base settings to work from:
MC21 Std bottom end, Wire splice, TYGA Pipes, Airbox lid mod with filter.
Temp: 29 C
Press: 1015mb
Hum: 65%
Alt: 30m
MJ – #182/#185
JN – Std./Std.
SJ – #38/#38
AS – 1.5 turns out
PwrJ – Std./Std.
Tip: Cooler temps, higher pressure and/or lower humidity require richer jetting. High altitude requires leaner settings. Starting off with rich settings will in the worse case foul a plug. Too lean a setting may destroy the engine.
This jet set-up is for guidance only. TYGA Performance cannot be held responsible for any engine damage incurred due to incorrect settings.
At present, this kit is available by special order. Each kit takes approx. four weeks to prepare.
TYGA no: TPER-3007Â
SKU: hon-10390 Categories: ALL products, High performance, High performance, High performance, High performance, Honda, NSR250 MC18, NSR250 MC21, NSR250 MC28, ShopCarbon frame cover (pair), Honda RVF400 NC35
€361.23
These lightweight carbon covers fit over the frame and they are designed to protect against scratches and damage to the frame in the event of an accident
TYGA no: BPCC-7418
SKU: hon-10625 Categories: ALL products, Bodywork, Bodywork and carbon, Bodywork and carbon, Honda, RVF400RR NC35Top Triple clamp CNC black, Suzuki RGV 250 VJ23 kit
€257.32
CNC machined top triple clamp with detachable ignition switch/lock holder for your RGV250 VJ23.
Designed and machined in house by TYGA, as a direct replacement for the OEM top triple clamp. FEA tested and developed for increased strength without unnecessarily increased weight.
Crafted from aircraft spec 6061-T6 alloy, the top triple clamp is ready to fit.
The detachable ignition switch/lock holder is positioned to allow use of the steering lock, but can be removed for race use.
Carbon fuel tank stay front, Suzuki RGV250 VJ21/VJ22
€60.24
Fuel Tank Stay, Front, Carbon, RGV250 VJ21/VJ22
This lightweight corrosion proof carbon stay replaces the stock item that the bike is supplied with.( Suzuki OE part nr: 44521-32C00-000.
It uses the stock mounting screws and can installed in seconds.
Fits Suzuki RGV250 VJ21 and VJ22
TYGA no: BPCC-0062
SKU: suz-10144 Categories: ALL products, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, RGV250 VJ21, RGV250 VJ22, Shop, Suzuki, Various parts, Various partsChoke Cable, RC36-2, RC30 Style
€11.29
Steering Stopper, Honda VFR750R RC36 (94-97)
Steering stopper for race use. Reduces degree of movement in steering. Easy to attach using hole for the horn on the standard lower triple clamp.
TYGA no: TYTO-0033
SKU: hon-11521 Categories: ALL products, Honda, RC36-2 -> RC30 replica products, Shop, Stocklist, various partsCarbon front fender support, Honda Monkey 125 2018-
€124.31
Carbon front fender support, Honda Monkey 125 2018-
Carbon direct replacement for original part. Lighter and looks way, way cooler!
TYGA no: BPCX-7542
SKU: msx-10431 Categories: ALL products, Bodywork and carbon, Honda, Monkey 125 2018-, ShopTYGA bike dust cover Black/red Force V4 Honda wing
€76.13
TYGA Bike Dust Cover, Blue, Rothmans Honda
This cover is handmade from 100% breathable polyester and ideal for an indoor dust cover. Suitable for sports bikes from 125cc to modern 1000cc. sportsbike, the cover features a pull-string around the bottom to secure it in position, comes with its own storage pouch and is machine washable.
Note, this is for indoor use only. For a weatherproof cover, see 08P34-KPP-700 Honda Bike Cover.
TYGA no: TMER-0170
SKU: hon-11315 Categories: ALL products, Bike covers, By model, Honda, Merchandise, Shop, Universal parts, Various parts, VFR400RR NC30Exhaustset stainless steel, oval stainless steel silencer w carbon cap, Honda PCX150
€493.21
.Set, Pipe, Full Race System, Oval Stainless Silencer, Carbon End Cap, PCX150
This full race system has been specifically designed for the PCX150 to maximise power. Made in stainless steel with spring mounted carbon silencer with carbon end cap, this system significantly increases performance, saves weight and enhances the looks of the bike. Sounds great too! (May not comply with noise regulations for some states and territories)
This system is supplied with a round carbon silencer with carbon end cap EXSL-00049
TYGA no: EXPS-0058
SKU: hon-10473 Categories: 4 stroke exhaust sets, ALL products, Exhausts, Honda, PCX150, Shop