Lower triple clamp CNC black, Honda RVF400 -> CBR600 fork
€367.66
Lower Triple Clamp, CNC Black, CBR600RR forks/NC35 shaft
CNC machined TYGA lower triple clamp for the NC35 RVF400 to take 53 mm diameter CBR600RR forks. (For later model CBR600RR which use 54 mm forks, we can supply by special order so please send us an email or put a comment with your or der that you need 54 mm and not the default 53mm.)
Designed and machined in-house by TYGA from aircraft spec 6061-T6 alloy. FEA tested and developed for increased strength without unnecessary weight increase.
This product does not include headstock seals or bearings. To complete the set we recommend you also order:
Seals: 53214-371-010 & 53214-KA4-701
Bearings: 91015-KT8-005 & 91016-KT8-005
This product is also sold as part of a set TYLY-1742, Triple Clamp Set, CNC Black, CBR600RR Forks to fit NC35.
TYGA no: TYLY-1942
SKU: hon-10550 Categories: ALL products, CNC parts, CNC parts, Honda, RVF400RR NC35, Shop, Stock list, all modelsKit, GRP, Complete bodywork set with Fuel Tank and Front Fender, painted Repsol, MC21, MC28 NSR250V
€3,668.44
Power Jet #0, for NSR250 MC18/21/28. Replica part to replace HRC part: 99106-NKD-970
Use this jet to blank of the power jet circuit in NSR250 carbs.
TYGA no: BPFS-250VREPSOL
SKU: hon-11411 Categories: ALL products, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, High performance, Honda, NSR250 MC21, NSR250 MC28, ShopCowling, Side, LH, Green, Ninja 250R 2008 -12
€259.23
Cowling, Side, LH, Green, Ninja 250R 2008 -12
TYGA no: 55028-0271-777
SKU: kaw-10196 Categories: ALL products, Kawasaki, Kawasaki OEM parts, Ninja 250R 2008- 12, ShopShroud left white, Honda MSX125 GROM
€32.45
Shroud left white, Honda MSX125GROM (msx-10017)
OEM Honda part
TYGA no: 83490-K26-900ZC
SKU: MSX-10017 Categories: ALL products, Honda, MSX125 2013 - 2015, OEM parts, ShopTail, Side Panel, Right, Green, Ninja 250R/300R 2013 -18
€70.70
Tail, Side Panel, Right, Green, Ninja 250R/300R 2013 -18
TYGA no: 53065-5019-777
SKU: kaw-10172 Categories: ALL products, Kawasaki, Ninja 250R 2008- 12, ShopInstrument holder, Ninja 400
€28.09
Instrument Holder, Ninja 400
Replacement instrument holder Ninja 400 suitable for TYGA race bodywork BPFS-0175
TYGA no: TYLY-0201
SKU: kaw-10139 Categories: ALL products, Bodywork and carbon, Kawasaki, Ninja 400R 2018-Top end rebuild set Cylinder A, Honda NSR250 MC21/MC28
€293.88
The picture shows everything you need to do a top end rebuild on your MC21/28. One kit includes all parts for one cylinder (cylinder ‘A’). To overhaul both cylinders please order 2 kits.
Honda OEM:
1x Gasket cylinder 12192-KV3-680
1x Gasket head 12251-KV3-830
1x Piston ring 13010-KV3-305
1x Piston B mark 13102-KV3-830
1x Piston pin 13111-KV3-771
1x RC valve shaft E clip 90601-KV3-000
1x Bearing piston 91102-KV3-771
1x Seal, RC valve shaft 91201-PA9-004
2x Dowel cylinder 94301-10160
2x Piston Circlip 15mm 94601-15000
There are different kits depending on the piston supplied and the pistons are sized to match the cylinder. The cylinders have a letter stamped on them. A cylinder = B piston B cylinder = no mark piston, C cylinder = D piston. The largest cylinder bore is A and the smallest is C. However, note that this is only for when cylinders are new or in good condition, so if the cylinder is worn, the corresponding piston will be a looser so a bigger piston might be advised. If the cross hatch honing of the cylinder is very feint then we suggest using the next size up piston. The differences in sizes are tiny (11 microns between largest and smallest) and for the most part not an issue so it is not a problem if a smaller piston is used in a larger cylinder or the other way round.
Cylinder A = 54.008mm – 54.011mm use Piston B = 53.966mm – 53.969mm
Cylinder B = 54.004mm – 54.008mm use Piston # = 53.962mm – 53.965mm
Cylinder C = 54.000mm – 54.004mm use Piston D = 53.958mm – 53.961mm
Piston to bore clearance = 0.039mm – 0.045mm
TYGA no: NHPS-0001A
SKU: hon-10439 Categories: ALL products, High performance, High performance, High performance, Honda, NSR250 MC21, NSR250 MC28, ShopCarbon end cap YZ250 silencer
€37.18
Tail Pipe, Stainless Steel, YZ250.
This link pipe is used in conjunction with the silencer, and is specific to the Yamaha YZ250
This product is compatible with EXCB-0032 and EXSL-0050 which together make up complete exhaust system EXTS-0001
TYGA no: EXCC-0007
SKU: alg-10142 Categories: 2 stroke exhaust sets, ALL products, Exhausts, Motocross, Shop, Yamaha, YZ250 2005-15