Bumb foam small,
€12.56
This foam seat bum stop is supplied with adhesive surface on back for easy and fast application. Adds the final touch to any race or race rep bike. This size is the smaller of the two versions we supply. See BPSP-0003 for larger version.
TYGA no: BPSP-0003
SKU: alg-10059 Categories: ALL products, Bodywork, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Bodywork and carbon, Honda, NSR250 MC21, NSR250 MC28, RVF400RR NC35, Shop, Various parts, Various parts, Various parts, Various parts, VFR400RR NC30TYGA / Kitaco Power up kit maggot , Honda MSX125 GROM
€702.49 €632.24
TYGA/KITACO Power Up Kit, Maggot Type
This power up kit is designed to give a significant power boost over stock. Using TYGA Performance and KITACO products, the power of the MSX125 Grom is increased by 25%. Below is the dyno graph. STD vs our full system with carbon silencer, Kitaco type 2 camshaft, i-map (setting #3). Similar results were found with the Moto Maggot and stainess type silencers.
Parts
This product consists of the components shown below, namely:
EXPS-0042 Set, Pipe, Full Race System, MSX125 Grom, Mot Maggot
KIT-300-1432010 KITACO Type 2 Camshaft
KIT-763-1432010 KITACO i-Map. Fuel Injection Controller
Option:
KIT-763-0500900 i-Map interface cable. To adjust the i-map for special setting. Software available on KITACO website.
For those who want a Type 1 camshaft, please put this in the commentbox at check out.
Description:
Fitting this Power Up Kit to your Honda MSX125/GROM gives a significant increase in top end performance and over rev. Peak hp is moved from 7,000rpm (std) up to 8,000rpm, with a 1.6hp gain at peak.
Fitting the i-Map Fuel Injection Controller is a necessary modification to avoid the engine running lean and being damaged. Running the KITACO Type 2 camshaft without the i-Map is NOT an option!
The wire harness requires modification and the documents are included with the kit, or can be viewed here: http://www.kitaco.co.jp/data/product/link/instaling_manual/kitaco_installing_manual_grom_imap.html
The i-Map is shipped with “setting #3” activated. This is the basic map for this kit, but the map can be modified using the optional i-Map interface cable and software downloadable from the KITACO website:
i-Map Fuel Manager: http://www.kitaco.co.jp/dlservice.html
TYGA no: TPER-0097
SKU: MSX-10306 Categories: ALL products, Exhausts, Exhausts, High performance, High performance, Honda, MSX125 2013 - 2015, MSX125SF 2016 -2020, ShopCarbon set, Aprilia RS250
€354.55
Carbon set, Aprilia RS250
Update your bike with these beautiful carbon products, same shape as original. Fits in minutes.
A set contains:
Front fender
Rear Hugger
Buy a complete set and it saves you money.
PLEASE NOTE: all ” TYGA” logo stickers on the carbon products can be easily removed because it is applied last above the clearcoat finish.
TYGA no: BPFS-0050
SKU: apr-10020 Categories: ALL products, Aprilia, Bodywork and carbon, Carbon, RS250, ShopSilencer clamp double GP 70mm (single bolt)
€34.12
Clamp, Silencer, GP, 70mm (1x Bolt)
Designed to securely clamp 70mm. O.D. silencers. Fabricated in 304 Stainless Steel with Molded rubber for secure, yet safe clamping.
This double clamp is used to clamp 70mm diameter silencers. For 61 mm silencers, see EXCL-0011 .
This product, EXCL-0005, does not have a tab above the top silencer and is suitable for applications where the silencers are not secured to the subframe with an exhaust stay or they are secured to the bike by use of a central position such as on the VJ22 with standard Suzuki subframe. This clamp holds the two silencers in position and, as such provides a certain amount of rigidity . If for your application, you would like to use an exhaust stay mounted to the subframe to hold the silencers securely, and you can’t bolt the exhausts to the rest of the bike using the central mounting bolt but want a mounting bolt above the silencers, then we recommend using EXCL-0004.
Compatible with the following TYGA systems, when used with our 70mm silencers, EXSL-0083 and EXSL-0084:
EXCS-0006A
EXCS-0006B
EXCS-0008
EXCS-0010
TYGA no: EXCL-0005
SKU: alg-10262 Categories: 2 stroke exhaust sets, ALL products, Aprilia, Exhausts, Exhausts, Exhausts, Exhausts, Exhausts, NSR250, NSR250 MC21, NSR250 MC28, RGV250 VJ22, RS250, ShopCarbon trim set, Honda MSX125SF GROM
€120.70
Trim, Set, (Carbon) MSX125SF
Carbon trim set to decorate your MSX125 Grom. Precision molded, these fit over the stock plastic stock items and transforms the appearance of your bike. Install with double sided tape provided or with silicone sealant for a really permanent installation.
TYGA no: BPFS-7328
SKU: MSX-10395 Categories: ALL products, Bodywork and carbon, Carbon, Honda, MSX125 GROM, MSX125SF 2016 -2020Set full race system high level with carbon silencer with carbon cap, Honda MSX125SF GROM
€519.40
Set, Pipe, Full Race System, High Level, MSX125SF Grom, Carbon Oval/Carbon End Cap. Second Generation.
This full race system has been specifically designed for the MSX125 to maximise power. Made in stainless steel with spring mounted carbon silencer this system increases performance, saves weight and enhances the looks of the bike. Sounds great too!
Total weight of the set is 2100 grams
Performance and Dynograph
The blue trace shows the 100% standard Honda MSX125 Grom, compared to the red trace, which is after installing the TYGA Full System set (EXPS-0043)
A useful gain all through the range, increasing as the revs rise up to maximum.
Similar Products:
Please also see:
EXPS-0065 Moto Maggot High level System for 2016 MSX125SF second generation Grom
EXPS-0067 Stainless Oval High level System for 2016 MSX125SF second generation Grom
Note: Some modification of the stock Honda rear hugger (no modification required if using the hugger BPCH-7028 and BPCH-7128) and stock Honda rear fender is necessary to install this system
Note, please check compatibility of under cowl/belly pan with exhaust before ordering. Our products are designed to fit the widest range of products and models but in some cases TYGA products made for the first generation MSX125 Grom are not compatible with the second generation. Please refer to table before ordering.
TYGA no: EXPS-0066
SKU: MSX-10339 Categories: ALL products, Exhausts, Honda, MSX125SF 2016 -2020, ShopExhaust set slip on, Motogp style stainless steel maggot , Honda MSX125 GROM
€307.40
Set, Pipe, Slip On, MSX125 Grom, Moto Maggot Silencer
Made in stainless steel with spring mounted aluminium silencer, this system significantly increases performance, saves weight and gives the best bang for the buck! (May not comply with noise regulations for some states and territories)
This system is supplied with a Moto Maggot EXSL-8013
Compatibility:
Note, please check compatibility of under cowl/belly pan with exhaust before ordering. Our products are designed to fit the widest range of products and models but in some cases TYGA products made for the first generation MSX125 Grom are not compatible with the second generation. Please refer to table before ordering.
TYGA no: EXPS-0034
SKU: MSX-10004 Categories: ALL products, Exhausts, Exhausts, MSX125 2013 - 2015, MSX125 GROM, MSX125SF 2016 -2020, ShopSet, Pipe, Full Race System, Ninja 250 2008-12, Moto Maggot Silencer
€491.32
This full race system has been specifically designed for the Ninja 250 to maximise power. Made in stainless steel with spring mounted aluminium silencer this system significantly increases performance, saves weight and enhances the looks of the bike. Sounds great too! (May not comply with noise regulations for some states and territories)
This system is supplied with a Moto Maggot silencer EXSL-4013
Independent Review:
TYGA Ninja 250R Race Exhaust System Dyno Results
October 29th, 2010 Adam
2008 Ninja 250R Dyno: TYGA Round Aluminum Race Exhaust System vs. Stock Exhaust
I’m a private party and this is my review of the TYGA Round Aluminum Race System. I am not a dealer, nor do I work for TYGA, but I’m a street rider and club racer. I’m reviewing this because I found little to no information regarding this system and I wanted to share my findings with others who found themselves in the same predicament as me (how can I pay less and not sacrifice performance!?!?). I scoured the internet but found no proof this system would give me any performance gains. I knew TYGA was a reputable manufacturer of quality products so I took a leap of faith and boy did it pay off!
Ninja 250R Dyno results are for the following runs:
Black: Stock Exhaust (no modifications whatsoever)
Blue: Stock Exhaust (snorkel removed)
Red: TYGA Round Aluminum Race System (snorkel removed)
Note: Carbs were not jetted. Fuel mixture screws were not adjusted.
HP Gains:
1) Remove snorkel ( 1.5HP) == 28.1HP!
2) Install TYGA Round Aluminum Race System ( 4.2HP) == 32.3HP!
Total: 5.7HP ( 4.2HP from TYGA exhaust!)
Weight Comparison (lbs):
Stock | Header: 4.1 | Can: 10.5**| Total: 14.6 lbs
TYGA | Header: 3.4*| Can: 2.6**| Total: 6 lbs
TYGA no: EXPS-0032
SKU: kaw-10086 Categories: 4 stroke exhaust sets, ALL products, Exhausts, Kawasaki, Ninja 250R 2008- 12